Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

Ceramics composites from iron ore tailings and blast furnace slag

The search for materials and methods capable of reducing human impacts on the environment is of utmost importance nowadays. This study's primary purpose was to analyze the technical feasibility of ceramic composites production utilizing Fundão Dam's Iron Ore Tailings (IOT), Blast Furnace Slag (BFS) from charcoal, and Foundry Sand (FS) as partial substitutes for the traditional raw materials – sand and clay – for application in building industry materials. The composites were molded in rectangular specimens and fired at temperatures of 900, 950, 1000, 1050, and 1200 °C. The developed materials were analyzed and characterized by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Thermogravimetry (TGA), and Differential Thermal Analysis (DTA). The obtained materials had flexural strength modulus of up to 12.19 MPa, water absorption ranging from 2 to 22%, linear shrinkage ranging from 0.02 to 6.50%, and apparent density ranging from 2.03 to 1.63 g/cm³. The study of the internal structure formation process revealed the formation of amorphous structures in the composites. The results demonstrated that these waste materials may be jointly used in construction materials, contributing to the reduction of natural resource extraction, besides enabling their correct disposal, minimizing environmental impacts, and improving the life quality of the surrounding communities.     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

射孔完井出砂预测新模型及其在射孔优化中的应用

分析了射孔完井的油层出砂机理，以线弹性理论为基础，考虑变温应力和流体渗流作用的拖曳力影响，建立了一种新的射孔完井出砂预测模型。应用该模型研究射孔方位、射孔参数对油井出砂的影响，结果表明，深穿透射孔弹比大孔半径射孔弹能更好地避免孔道出砂，采用定向射孔能有效地减少油井出砂问题。其结果对砂岩油藏射孔优化设计具有一定指导意义。     

川东气藏直井完井方法的产能预测研究

在分析研究目前国内外油气井完井产能计算经验公式的基础上，针对四川气田东部浅层气藏常用的几种完井方式，建立了该地区完井产能预测的数学模型。通过实例计算，表明了其数学模型的准确可行性，并为出砂井和非出砂井的完井方式提供了选择依据：对于出砂井，砾石裸眼充填完井方式是最理想的完井方式；对于非出砂井，实际裸眼完井的产能最大。得出的结论对该地区直井完井方式的选择，完井参数优化设计以及产能预测具有一定的指导作用。     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。     

琼东南盆地深水区储层分布规律

琼东南盆地深水区经历了断陷、断拗和拗陷3大构造演化和沉积充填阶段,主要发育4种沉积体系,相应地形成了4类主要储层:1)陵三段扇三角洲或滨海相砂岩储层;2)三亚、梅山组滨浅海相砂岩储层;3)三亚—莺黄组低位体储层;4)梅山组台地边缘礁滩灰岩储层。平面上,储层发育具有明显的分带性,可划分为:北部浅水陆架滨岸砂岩、三角洲砂岩储层发育带;中央坳陷低位体储层发育带;南部永乐隆起区碳酸盐岩储层发育带。深水区主要位于后2个带,每个带储层发育的控制因素不同,可以进一步划分为多个储层发育区。每个储层发育区存在多套储盖组合,每套储盖组合在多个储层区中发育。其中台地灰岩储层可能成为南部隆起区具有重要意义的勘探层系。      

非稳定井流模型的半解析解

为了提高非稳定渗流计算的计算精度 ,通过数学分析得到了水位传导系数随时间变化时 ,一类非稳定渗流井流模型的半解析解 ,并进行了计算比较     

辽河防洪应急工程中的加筋粉细砂筑坝技术

加筋粉细砂筑坝是一门新兴技术,通过在辽河防洪应急工程右岸李家堡段应用表明,该项技术在技术上是可行的、在经济上是合理的。本文介绍了该技术在辽河防洪应急工程右岸李家堡段的应用。     

单片LCoS光学引擎中彩色LED照明系统设计

LCoS光学引擎作为整个背投的一个要组成部分，其照明系统显著地影响着LCoS背投的性能。详细分析了影响照明效果的各个因素，并利用ZEMAX软件设计出了单片LCoS光学引擎中基于彩色LED光源的照明系统，该系统能达到较好的亮度和均匀性，满足整个光机系统的成像要求。