Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

Event-triggered distributed receding horizon control for tracking and formation of homogeneous multi-agent systems

This paper proposes an event-triggered distributed receding horizon control (DRHC) approach for the formation and tracking problems of homogeneous multi-agent systems. For each agent, an event-triggering condition, based on assumed predictive information of the neighbours, is derived from stability analysis. Considering the uncertain deviation between the assumed and true predictive information, we design a time-varying compatibility constraint for the individual optimization problem. In the event-triggered DRHC algorithm, each agent solves the optimization problem and communicates with its neighbours only when the event-triggering condition is satisfied, so the communication and computation burden are reduced. Moreover, guarantees for the recursive feasibility and asymptotic stability of the overall system are proved. A simulation example is provided to illustrate effectiveness of the proposed approach.     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

Study on wax precipitation characteristics of wax deposit in pipes

Wax deposit properties are a significant concern in pipeline pigging during waxy crude oil transportation. In the present work, the impacts of flow conditions and oil properties on the wax precipitation characteristics of wax deposits are investigated. A flow loop apparatus was developed to conduct wax deposition experiments using four crude oils collected from different field pipes. The differential scanning calorimetry (DSC) technique was employed to observe the wax precipitation characteristics of crude oil and wax deposit. The results show that the wax content and the wax appearance temperature (WAT) of the deposits increase with shear stress and radial temperature gradient, and decrease with radial wax molecule concentration gradient near the pipe wall. The DSC tests on the wax deposits revealed that the deposit wax content is strongly correlated to the oil wax content. Furthermore, an empirical correlation was developed to predict the wax content and the WAT of the wax deposit. Verification of the empirical correlation using the different oils indicated that the average relative error of the wax content prediction and average absolute error of WAT prediction were 13.2% and 3.6°C, respectively.     

低剂量抑制剂Inhibex501存在下的甲烷水合物相平衡研究

含动力学抑制剂的天然气水合物相平衡研究对新型低剂量抑制剂的开发具有指导作用。在283.6 ~ 290.9 K和7.51 MPa ~ 15.97 MPa的温压范围内研究了抑制剂Inhibex501及其溶剂2-乙二醇单丁醚对甲烷水合物相平衡条件的影响。实验结果显示，0.5wt%和2.0wt%浓度的Inhibex501对甲烷水合物形成的热力学条件具有促进作用，能使甲烷水合物形成移向更高的温度或者更低的压力，而2-乙二醇单丁醚在浓度0.2wt% ~ 1.0wt%范围几乎不改变甲烷水合物形成的热力学条件，N-乙烯基己内酰胺与N-乙烯基吡咯烷酮的共聚物对水合物形成热力学条件的改变起主要作用。     

一种新的解映射算法的推导和实现

本文在一种16QAM,64QAM,256QAM的解映射算法启发下,提出了新的适合32QAM和128QAM的解映射算法,并在此基础上,给出了适合DVB-C接收机的多QAM解映射结构.然后在FPGA中实现和仿真.最后通过比较说明,相对于传统的查找表解映射方法,提出的解映射算法可以明显减少资源使用率.     

GIS在深圳市三防指挥信息系统中的应用

深圳市三防指挥信息系统利用GIS技术,结合水利(水务)、防汛、抗旱的具体业务,建立了水情遥测数据处 理分系统、工况监测数据处理分系统、水务行业三防信息管理分系统、决策支持分系统、水源优化调度分 系统,提高了现代化管理水平。     

提高催化裂化装置(FCCU)柴汽比措施

为了满足市场的需要,中石化天津分公司炼油厂根据FCCU自身特点采取了一系列提高柴汽比的措施,包括:调节反应系统和分馏的操作条件及采用MGD技术,以提高柴油产率。实施后,FCCU的柴汽比从0.5提高到0.9,创造了良好的经济效益。     

结构振动试验转接器的设计及安装问题

一些产品及其相关部件在作振动试验时，由于产品的外形或特殊要求不能直接安装在振动台面上，需要通过特别设计的转接器（夹具）来进行连接，这种夹具实际上是一种附加结构，它作为台面与试件之间的中介，如设置不当将影响振动试验结果的可靠性。本文通过对某事例的分析与研究，从试验频带、允许误差、跟随条件以及安装共振频率等方面阐明与讨论了相关夹具的特性、设计原则与安装等问题。     

Controlled elements for designing ciphers suitable to efficient VLSI implementation

This work considers the problem of increasing the performance of the ciphers based on Data-Dependent (DD) operations (DDO) for VLSI implementations. New minimum size primitives are proposed to design DDOs. Using advanced DDOs instead of DD permutations (DDP) in the DDP-based iterative ciphers Cobra-H64 and Cobra-H128 the number of rounds has been significantly reduced yielding enhancement of the “performance per cost” value and retaining security at the level of indistinguishability from a random transformation. To obtain further enhancement of this parameter a new crypto-scheme based on the advanced DDOs is proposed. The FPGA implementation of the proposed crypto-scheme achieves higher throughput value and minimizes the allocated resources than the conventional designs. Design of the DDO boxes of different orders is considered and their ASIC implementation is estimated.