Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method

A new technique of EDM coring of single crystal silicon carbide (SiC) ingot was proposed in this paper. Currently single crystal SiC devices are still of high cost due to the high cost of bulk crystal SiC material and the difficulty in the fabrication process of SiC. In the manufacturing process of SiC ingot/wafer, localized cracks or defects occasionally occur due to thermal or mechanical causes resulted from fabrication processes which may waste the whole piece of material. To save the part of ingot without defects and maximize the material utilization, the authors proposed EDM coring method to cut out a no defect ingot from a larger diameter ingot which has localized defects. A special experimental setup was developed for EDM coring of SiC ingot in this study and its feasibility and machining performance were investigated. Meanwhile, in order to improve the machining rate, a novel multi-discharge EDM coring method by electrostatic induction feeding was established, which can realize multiple discharges in single pulse duration. Experimental results make it clear that EDM coring of SiC ingot can be carried out stably using the developed experimental setup. Taking advantage of the newly developed multi-discharge EDM method, both the machining speed and surface integrity can be improved.     

Survey on Passivity Based Control of Induction Machine

Induction machines (IM) constitute a theoretically interesting and practically important class of nonlinear systems. They are frequently used as wind generators for their power/cost ratio. They are described by a fifth‐order nonlinear differential equation with two inputs and only three state variables available for measurement. The control task is further complicated by the fact that IM are subject to unknown (load) disturbances and the parameters can be of great uncertainty. One is then faced with the challenging problem of controlling a highly nonlinear system, with unknown time‐varying parameters, where the regulated output, besides being unmeasurable, is perturbed by an unknown additive signal. Passivity‐based control (PBC) is a well‐established structure‐preserving design methodology which has shown to be very powerful to design robust controllers for physical systems described by Euler‐Lagrange equations of motion. PBCs provide a natural procedure to "shape" the potential energy yielding controllers with a clear physical interpretation in terms of interconnection of the system with its environment and are robust vis á vis to unmodeled dissipative effects. One recent approach of PBC is the Interconnection and Damping Assignment Passivity‐Based Control (IDA‐PBC) which is a very useful technique to control nonlinear systems assigning a desired (Port‐Controlled Hamiltonian) structure to the closed‐loop. The aim of this paper is to give a survey on different PBC of IM. The originality of this work is that the author proves that the well known field oriented control of IM is a particular case of the IDA‐PBC with disturbance.     

两相异步电动机变频调速装置

主要讨论对称两相变频器主电路的结构以及介绍一种简单实用的磁链轨迹控制技术．     

数学归纳法的几个推广

将通常适用于自然数系的数学归纳法推广到了下有界整数集{n|n∈Z,n≥n0}与上有界整数集{n|n∈Z，n≤m0}及全体整数集Z。并证明了关于命题{P(m,n)}m,n∈z的二元数学归纳法。     

自适应电子镇流器控制器IR2520原理及应用

IR2520是自适应镇流器控制器与600V半桥驱动器单片IC ,可用来驱动半桥配置中的荧光灯。文中介绍了IR2520的主要特点和基本原理 ,给出了它的典型应用电路。     

二阶A型Cooper变换的增强型

对二阶Ａ型Ｃｏｏｐｅｒ变换进行增强，放宽可用性条件，并证明了其正确性，最后举例说明其应用。     

Numerical solution of the kinematic dynamo problem for Beltrami flows in a sphere

The article discusses computational aspects of the kinematic problem of magnetic field generation by a Beltrami flow in a sphere. Galerkin's method is applied with a functional basis consisting of Laplace operator eigenfunctions. Dominant eigenvalues of the magnetic induction operator and associated magnetic eigenmodes are obtained numerically for a certain Beltrami flow for magnetic Reynolds numbers up to 100. The eigenvalue problem is solved by a highly optimized iterative procedure, which is quite general and can be applied to numerical treatment of arbitrary linear stability problems.