涤纶工业丝环吹风改造的设计计算

应用PET纤维的冷却成形理论 ,结合空气调节的相关知识 ,提出了环吹风的设计计算方法 ,对涤纶工业丝环吹风进行了设计改造 ,满足了纺丝工艺要求     

液闪效率示踪法校正效果的评价

本文评价了Aloka商品液闪仪效率示踪法dpm校正的效果。轻,中度猝灭校正效果理想,具有简便、实用和适用性广泛的特点。严重化学和颜色猝灭样品的校正结果分别随猝灭增加而向增大和减小的方向偏离,形成喇叭状曲线,文中对这一现象给出初步解释。     

OFA-II型定量荧光仪在油气勘探中的应用

定量荧光仪在现场应用中受到各种因素的影响:如岩屑样品浸泡时的干、湿;图谱是否出现了淬灭;环境温度的影响等等。文章通过具体事例给出解决这些问题的办法。     

溶胶—凝胶法制备基于荧光猝灭原理的光纤氧传感器在线监测水中溶解氧

利用氧分子对金属钌化合物的荧光具有猝灭作用的特性,构造出基于荧光猝灭原理的光纤氧传感器。就用于水中溶解氧在线监测的光纤光谱仪的搭建、传感器探头的设制及传感膜的制作过程进行探索,并对传感器的响应性能进行考察。结果表明以联吡啶钌等作为荧光指示剂以溶胶-凝胶法制备的传感膜对溶解氧的响应具有良好的可逆性,稳定性,较快的响应时间和较长的使用寿命。与标准法相对照,用本仪器系统测定了不同盐度的人工海水中的溶解氧浓度,两种方法在不同浓度水平下的溶解氧测定值均无显著性差异。本法的日内和日间RSD在1.7％～5.0％之间。     

Surface Hardening of High-Strength Low Alloy Steels (HSLA) Dual-Phase Steels by Ball Burnishing Using Factorial Design

Burnishing is used increasingly as a finishing operation which gives additional advantages such as increased hardness, fatigue strength, and wear resistance. Experimental work based on 3⁴ factorial design was carried out to establish the effects of ball burnishing parameters on the surface hardness of high-strength low alloy steels (HSLA) dual-phase (DP) steel specimens. Statistical analysis of the results shows that the speed, feed, lubricant and ball diameter have significant effect on surface hardness.     

丙烯腈急冷塔喷淋系统流道分析与优化

对国内现有丙烯腈装置急冷塔循环液喷淋器的分流流道进行了研究。对喷头堵塞情况作了理论分析，并运用计算机编程模拟计算出喷淋器中各喷头的流体分布情况。在此基础上提出了分流流道的优化方案，从而改善了急冷塔内的操作状况，减少了丙烯腈在急冷塔内的损失。     

DIN-100MnCrW4模具钢开裂原因分析

对DIN－100MnCrW4模具钢开裂原因进行了分析。结果表明，模具钢 属淬火开裂，主要原因是材料内部组织不均匀所致。     

球磨机衬板材料及热处理工艺

对传统的中碳低合金耐磨铸钢的化学成分和热处理工艺进行了优化设计 ,使新材料具有较高的强度、硬度和韧性 ,因而抗冲击、抗疲劳、抗磨损性能良好。实际应用表明 ,用此种材料代替油淬和风冷中碳低合金耐磨铸钢 ,不仅生产成本低 ,而且在矿山、电力球磨机制粉等工矿条件下 ,其使用寿命长     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

荧光消除剂的应用研究

介绍了一种粉末状荧光消除剂的应用特性,并对影响荧光消除剂使用效果的因素进行了探讨。结果表明,浆料温度及荧光消除剂与浆料的混合作用时间对荧光消除效果有较大影响。