微机械可调谐滤波器的研制

利用 Ga As/Al Ga As分布反馈 Bragg反射镜在 Ga As衬底上制作了一个微机械的调谐滤波器 .该器件在 7V调谐电压下调谐范围达28nm     

Photoluminescence and X-ray Diffraction of Distributed Bragg Reflector

Spectral and structural characteristics of distributed Bragg reflector (DBR) in vertical-cavity surface-emitting lasers were studied with photoluminescence and double- crystal X- ray diffraction measurement. The expected high quality epitaxial DBR structure was verified. In the X- ray double- crystal rocking curves of DBR the zeroth- order peak, the first and second order satellite peaks were measured. Splitting of diffraction peak appeared in the rocking curves was analyzed. The effects of introduced deep energy levels on the structural perfection and optical properties were discussed.     

A Survey of Inverse Surface Design From Light Transport Behavior Specification

Inverse surface design problems from light transport behavior specification usually represent extremely complex and costly processes, but their importance is well known. In particular, they are very interesting for lighting and luminaire design, in which it is usually difficult to test design decisions on a physical model in order to avoid costly mistakes. In this survey, we present the main ideas behind these kinds of problems, characterize them, and summarize existing work in the area, revealing problems that remain open and possible areas of further research.     

底支承对小口径反射镜镜面变形的影响

论述了运用有限元技术研究镜面变形的方法及分析底支承在不同口径，焦比、厚径比和相对支承半径时镜面变形的技术；在取得的相互关联的最大镜面变形数据基础上，研究了影响小口径反射镜底支承镜面变形的因素。     

Characterization of microspherical semi-transparent solar cells and modules

Microspherical solar cells and modules have been fabricated. The spherical nature of these semi-transparent devices allows the microspherical cells to harvest both directly incident and diffuse components of sunlight thereby improving the solar energy conversion efficiency. Indoor and outdoor characterizations of these three dimensional semi-transparent cells and modules are carried out using a Lambertian reflector in order to assess the maximum efficiency of the devices. In the absence of the reflector the cell efficiency is 13.5% under standard illumination (100 mW cm⁻², A.M. 1.5, 25 °C). However, this is significantly enhanced in the presence of the reflector. Microspherical modules with the reflector are directly compared to similar semi-transparent modules comprised of traditional planar devices, in outdoor tests at low light intensity (2.5–25 mW cm⁻²) to further demonstrate the benefits of the design particularly at low angle of incident radiation.     

星载成形反射面天线的设计方法

成形反射面天线的设计与综合是近年来卫星天线发展的一个热点问题 ,本文对日本、北美和欧洲成形反射面天线的技术发展和综合方法作了介绍和比较。     

用于LED光源的反光杯准直效果研究

为研究抛物面型反光杯用于LED光源准直时的特点,基于TracePro仿真了LED光源在不同尺寸反光杯下的有效射程和光斑直径,分析了反光杯和LED尺寸对射程和光斑直径的影响。仿真结果表明:射程与反光杯的口径和深度都有关系。高度相同时,反光杯口径越大,射程越大;口径相同时,射程随反光杯高度增加先增大后减小。LED光源经反光杯准直,较短距离的光斑中心光强很低,形成光环。LED光源面积直接影响目标面光斑的大小,对射程影响较小。     

空间薄膜反射镜圆薄膜模态分析

空间薄膜反射镜是一种空间应用新技术。聚酰亚胺圆薄膜的模态分析能够给薄膜反射镜夹持结构的设计和动态特性分析提供重要依据。通过对薄膜振动贝塞尔方程的求解,得到了300mm聚酰亚胺圆薄膜的前四阶振动频率,并利用ANSYS有限元仿真软件进行了模拟验证,求得了前四阶振型和相应振动频率。薄膜反射镜的固有频率很低,一阶固有频率为9.3Hz左右。这对于反射镜夹持结构和整个光学系统设计,以及载荷的施加、面形调整等提出了特定要求,以避免发生共振影响工作。     

DBR光纤激光器拍频传感及其组网技术研究

研究了基于单纵模分布Bragg反射(DBR)光纤激光器的拍频解调传感技术,并对其组网技术进行了探讨。由于光纤本身的固有双折射,DBR光纤激光器能够产生两种正交偏振模式的激光,而这两种偏振模式的频率差拍会在射频域形成对温度变化极为敏感的拍频(beatfrequency)。实验结果表明:在20～100℃的温度范围内,激光器拍频随温度的增加呈线性减小,其线性拟合度高达0.99981,拍频灵敏度为0.51063MHz/℃。这种偏振式光纤激光器具有高输出功率、高信噪比、低解调成本和窄输出线宽等特点,有助于构建大规模的光纤有源传感网络。参考近年关于光纤传感网络的报道,提出一种有源光纤环形传感网络的构想。     

偏馈式构架反射器展开冲击特性分析

As the off-fed truss reflector is connected to the platform by a single edge and deployed rapidly through being driven by the spring, the impact influence acts obviously on both the reflector and the platform. Due to limitations of the ground test, the in-orbit deployment impact characteristics of truss reflector are difficult to obtain. Then, by taking a certain reflector as the research object, a dynamic model is established with multibody dynamic software. Based on the modified model with ground deployable tests, in-orbit deployment impact characteristics are obtained by simulation analysis. Therefore, the method for multibody dynamic modeling is suitable for truss reflector dynamic research, and the result is useful for the deployable reliability optimization.