Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

基于谐振原理的硅微机械加速度计

基于力学振动原理 ,导出敏感梁类谐振振动的微分方程 ,给出了振梁型加速度计的设计原理。指出了加速度计谐振梁频率的相对变化量与梁的厚度无关 ;为避免输出非线性频率信号 ,频率的相对变化率和激励振动的振幅都不宜太大     

纳米加工和纳米电子器件

介绍了电子束曝光技术、EUV光刻技术和X射线光刻技术的进展;对各种纳米电子器件如单电子器件、共振隧穿器件和分子电子器件的研究现状及面临的主要挑战进行了讨论。     

可见光共振腔发光二极管的研究进展

共振腔发光二极管是一种具有优良发光性能的光电器件。概述了对可见光共振腔发光二极管的共振腔结构、反射镜材料体系、基本工作机理和发光特性，并展望了这种器件的发展前景。     

Modeling Spin-Dependent Transport in InAs/GaSb/AlSb Resonant Tunneling Structures

The Rashba effect resonant tunneling diode is a candidate for achieving spin polarizing under zero magnetic field using only conventional non-magnetic III–V semiconductor heterostructures. We point out the challenges involved based on simple arguments, and offer strategies for overcoming these difficulties. We present modeling results that demonstrate the benefits of the InAs/GaSb/AlSb-based asymmetric resonant interband tunneling diode (a-RITD) for spin filtering applications.     

光激励和光检测微型硅谐振器研究

分析了光激励谐振器振动的检测问题，用调制激光束激励谐振器使其发生振动，并采用光学干涉的方法测量了这种微振动。     

单模光纤的传输衰减随温度变化的研究

本文从实验上测量了单模石英光纤在－50～120℃范围内的损耗。随着温度升高，光纤的损耗随之降低，在常温附近达到最小。其后损耗随着温度的继续升高而增加。损耗的变化主要是由于杂质的吸收和微弯损耗。本文对杂质的吸收以及微弯损耗进行了数值模拟，并且从理论上定性地解释了损耗对温度的依赖关系。     

压阻式硅微加速度传感器的结构设计与仿真

一般的压阻式硅微加速度传感器结构多采用单梁加质量块的形式,这种形式的传感器灵敏度比较高,但它的横向效应较难克服,文中提出一种四梁结构的加速度传感器,通过仿真计算,说明该结构的加速度传感器具有良好的综合特性.     

一种新型谐振腔增强型光调制器结构的研究

提出了一种新型谐振腔增强型(RCE)光调制器结构,它由一个对称型谐振腔增强型光调制器和一个高反镜所构成.利用传输矩阵法对该器件的插入损耗及临界吸收厚度进行了模拟分析,并同传统谐振腔增强型光调制器的相关性能进行了比较.分析结果表明,这种结构解决了传统谐振腔增强型光调制器的临界吸收厚度与插入损耗之间相互制约的矛盾,可同时获得低临界吸收厚度和低插入损耗.