Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

浅析智能网联汽车感知系统电磁兼容性

本文将就智能网联汽车感知系统中的电子兼容技术进行深入的分析和探究。     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

电喷雾质谱法示踪钨回收过程离子的转化路径

将环隙式离心萃取器(ACCs)与电喷雾飞行时间质谱(ESI-TOF-MS)相结合，在线监测了回收过程中的钨萃取行为(宏观)和钨形态的转化路径(微观)，发现宏观萃取反应和微观离子形态转化同时发生并相互补充。伯胺N1923萃取钨在144 s内即可达到萃取平衡，萃取率高达98%以上，同时，酸钨比n(H)/n(W)是一个关键变量，当酸钨比n(H)/n(W)=2.4时，全流程钨回收率超过93%。最后，得到了基于钨形态监测的萃取机理，同时，减少原料液中W1含量，增加W10含量，可有效提高钨回收效率。     

食物成瘾的研究进展及启示

食物成瘾是一种复杂的慢性疾病，导致人们在日常生活中对某种食物产生过度依赖与过度进食等相关行为特征，近年来已被认为是影响欧美发达国家肥胖症、暴食症、糖尿病等发病率持续升高的关键原因，引起学术界的极大关注，成为研究热点。本文主要介绍食物成瘾的概念、诊断标准，综述了食物成瘾的病理机制、影响因素和应对措施等方面的研究进展，并探讨食物成瘾对我国食品界的启示，为预防食物成瘾，保障公众健康提供有益借鉴。     

Operational time-series data modeling via LSTM network integrating principal component analysis based on human experience

Today’s information technologies involve increasingly intelligent systems, which come at the cost of increasingly complex equipment. Modern monitoring systems collect multi-measuring-point and long-term data which make equipment health prediction a “big data” problem. It is difficult to extract information from such condition monitoring data to accurately estimate or predict health statuses. Deep learning is a powerful tool for big data processing that is widely utilized in image and speech recognition applications, and can also provide effective predictions in industrial processes. This paper proposes the Long Short-term Memory Integrating Principal Component Analysis based on Human Experience (HEPCA-LSTM), which uses operational time-series data for equipment health prognostics. Principal component analysis based on human experience is first conducted to extract condition parameters from the condition monitoring system. The long short-term memory (LSTM) framework is then constructed to predict the target status. Finally, a dynamic update of the prediction model with incoming data is performed at a certain interval to prevent any model misalignment caused by the drifting of relevant variables. The proposed model is validated on a practical case and found to outperform other prediction methods. It utilizes a powerful deep learning analysis method, the LSTM, to fully process big condition monitoring series data; it effectively extracts the features involved with human experience and takes dynamic updates into consideration.