The World robot summit disaster robotics category – achievements of the 2018 preliminary competition

The World Robot Summit is a robot Olympics and aims to be held in a different country every four years from 2020. The concept of the Plant Disaster Prevention challenge is daily inspections, checks, and emergency response in industrial plants, and in this competition, robots must carry out these types of missions in a mock-up plant. The concept of the Tunnel Disaster Response and Recovery challenge is emergency response to tunnel disasters, and is a simulation competition whereby teams compete to show their ability to deal with disasters, by collecting information and removing debris. The Standard Disaster Robotics challenge assesses, in the form of a contest, the standard performance levels of a robot that are necessary for disaster prevention and emergency response. The World Robot Summit Preliminary Competition was held at Tokyo Big Sight in October 2018, and 36 teams participated in the Disaster Robotics Category. UGVs and UAVs contended the merits of new technology for solving complex problems, using core technologies such as mobility, sensing, recognition, performing operations, human interface, autonomous intelligence etc., as well as system integration and implementation of strategies for completing missions, gaining high-level results.     

大牛地气田异常修正等时试井资料求取产能方法

大牛地气田为低渗-致密气田,因存在启动压力梯度等因素,修正等时试井曲线按常规方法处理出现异常,无法准确获取气井的产能方程.采用LIT法和异常曲线校正法对气田异常试井资料进行了重新处理,最终获得气井产能方程,为同类气藏产能试井可能出现的异常资料处理解释探索了新的途径.     

纤维在沥青混合料中的应用研究

选用工程中常用的几种纤维,结合工程应用要求,试验分析了纤维的吸湿性、耐热性,并通过网篮析漏试验、动态剪切试验和沉锥试验,讨论了纤维对沥青的稳定和吸附作用,以及纤维对沥青混合料“加筋”效果和作用机理。研究表明有的纤维“吸附、稳定”性能好,而有的纤维“加筋、桥接”效果好,在应用纤维时,应根据纤维的主要特点以及沥青混合料的使用要求来选用。     

汽车计算平台工程国外相关标准概述

结合我国汽车计算平台工程,分析了国外相关的标准现状和基本框架,并为今后工作的开展提出了建议.     

微制造平台微振动的最优控制

采用混合隔振技术建立了微制造平台隔振系统。该系统以空气弹簧和橡胶层作为被动隔振元件、超磁致伸缩致动器作为主动隔振元件，并采用最优控制理论设计其主动控制器。研究了在不同的性能指标加权阵的情况下，该主动振动控制系统对基础干扰和由微制造设备产生的直接干扰所引起的微制造平台振动的控制效果。研究表明性能指标加权阵对振动控制效果影响非常大。通过大量的仿真实验确定了一组性能指标加权阵，使所设计的主动控制系统能在较宽的频率范围对基础干扰和直接干扰所引起的微制造平台振动进行有效的控制。     

Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

地杂波O．94μm激光后向反射率测试研究

通过对地杂波O．94μm激光后向反射率的测试，获取不同入射角的多背景后向反射率测试数据。通过对测试数据的分析处理提供特征信息，为激光探浏器设计提供依据。     

射孔枪+内置式压力计托筒+水力泵新三联作试油(测试)工艺技术在大港油田研制与应用

该工艺技术是在原三联作(TCP+MFE+JET)基础上,根据大港油田勘探试油(测试)的需要,研制开发出的又一新技术,与原三联作相比,一趟管柱不但完成求产、测压、泵排工作,而且还能进行酸化等措施,提高了资料品质,减少了作业成本。经过6井次现场应用,全部达到了设计要求,取得了工艺、资料、成本、速度的较大进步,具有较高推广应用价值。     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。