Numerical study on laminar burning velocity of ammonia flame with methanol addition

The combustion characteristics of ammonia/methanol mixtures were investigated numerically in this study. Methanol has a dramatic promotive effect on the laminar burning velocity (LBV) of ammonia. Three mechanisms from literature and another four self-developed mechanisms constructed in this study were evaluated using the measured laminar burning velocities of ammonia/methanol mixtures from Wang et al. (Combust.Flame. 2021). Generally, none of the selected mechanisms can precisely predict the measured laminar burning velocities at all conditions. Aiming to develop a simplified and reliable mechanism for ammonia/methanol mixtures, the constructed mechanism utilized NUI Galway mechanism (Combust.Flame. 2016) as methanol sub-mechanism and the Otomo mechanism (Int. J. Hydrogen. Energy. 2018) as ammonia sub-mechanism was optimized and reduced. The reduced mechanism entitled ‘DNO-NH3’, can accurately reproduce the measured laminar burning velocities of ammonia/methanol mixtures under all conditions. A reaction path analysis of the ammonia/methanol mixtures based on the DNO-NH3 mechanism shows that methanol is not directly involved in ammonia oxidation, instead, the produced methyl radicals from methanol oxidization contribute to the dehydrogenation of ammonia. Besides, NO_x emission analysis demonstrates that 60% methanol addition results in the highest NO_x emissions. The most important reactions dominating the NO_x consumption and production are identified in this study.     

Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

预分解窑燃无烟煤生产水泥熟料技术及其应用

无烟煤着火温度高、燃烧速度低、燃烬时间长,故一直难以用作回转窑燃料.20世纪90年代,南京院率先进行了回转窑燃无烟煤生产的研究开发.经10多年的努力,解决了所有的技术问题,开发了配套的专有装备,已在福建三德水泥厂、福建南平水泥公司、龙岩春池集团、广西鱼峰水泥公司等厂的多条生产线上应用并获巨大成功.     

Filtration of Non-Newtonian Hydrocarbon Fluid in a High-Frequency Electromagnetic Field

The paper gives the results of experimental investigations of the initial pressure gradient of bituminous oil and the time dependences of variation of the temperature in a formation model and of the well production rate in a microwave-frequency electromagnetic field. The effect of strong decay of the non-Newtonian properties of bituminous oil is revealed. The nonuniformity of temperature distribution over the formation thickness is demonstrated, which depends on the initial production rate of the well and on the duration of stimulation of the bottom-hole zone of formation.     

热处理对Ti-25V-15Cr-2Al-2Mo-0.2C合金组织稳定性的影响

研究了热处理对Ti-25V-15Cr-2A1-2Mo-0.2C阻燃β钛合金组织稳定性的影响。结果表明，高温固溶并直接时效处理导致合金β基体上析出较多的α相沉淀，尤其在随后的热暴露组织中形成了恶化合金塑性的连续晶界α膜。然而，若在时效前再进行一次低温固溶处理则可明显减少α相的析出数量，合金的热稳定性因此而得到显著改善。     

科学焚烧垃圾系统的技术特点

科学焚烧处理垃圾法具有占地少,场地易选择,时间短,减量化显著,无害化彻底以及回收余热供发电供热等优点.其处理设备和控制系统是保证科学焚烧处理垃圾成功,并带来巨大经济效益的关键.鉴于此,文章对科学焚烧垃圾系统设计作了比较详细的介绍.     

1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。     

含多孔物质硝胺发射药的温感特性

研究了多孔物质对于硝胺发射药在不同初温下的燃面调节作用，由于多孔物质的孔结构及其与基体界面状况的改变，使发射药低温燃面增大，而高温燃面减小，这有利于降低燃速温度系数．     

梅山2号高炉内燃式热风炉获高风温的生产实践

介绍了梅山2号高炉（1280m^3）引进奥钢联的改进型内燃式热风炉技术；论述了其主要结构特点和设计参数；分析了其采用附加高炉煤气为燃料的燃烧炉管束式换热器的运行情况。实践表明，在以全高炉煤气为燃料的内燃式热风炉上实现了1200℃以上的高风温。     

Prediction of fire classification for wood based products. A multivariate statistical approach based on the cone calorimeter

Wood has long traditions as a building material, and is often used in construction elements, and as interior and exterior surfaces in the Nordic countries. In most applications, there are reaction to fire requirements to products used as surfaces, e.g. in escape routes and larger public spaces. Most wood products will therefore have to be treated with fire retardant (FR) agents to fulfil the strict requirements to properties connected to heat release and flame spread. Unfortunately, FR agents usually also increase the smoke production, as they cause a more incomplete combustion of the wood. The wood product manufacturers seek to find the optimal amount of FR additives where both heat release and smoke production in the classifying test are within the requirements given in the building regulations. This paper describes models for prediction of the European reaction to fire classes of wood products. The models are based on multivariate statistical analysis, and use test results from the cone calorimeter test as input. The presented models are, with very good precision, able to predict which Euroclass and additional smoke class a wood based product would obtain if it were to be tested in the single burning item test. Copyright © 2006 John Wiley & Sons, Ltd.