Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

焊接方法对双相不锈钢焊接接头力学性能的影响

研究了不同焊接方法对SAF2205双相不锈钢板焊接接头金相组织和力学性能的影响,结果表明,采用不同焊接方法得到的焊接接头的铁素体与奥氏体两相比例不同,使焊接接头的力学性能存在较大差异,对实际生产中SAF2205双相不锈钢的焊接具有一定的指导意义。     

新一代高强韧性WDL系列钢综合性能及应用

本文着重介绍武汉钢铁公司近年来研制开发的第二代高强度低合金钢—高强韧性WDL系列钢的综合性能及应用情况。该钢具有优异的焊接性能和低温韧性,板厚≤50mm钢板焊前不预热或稍加预热而不产生焊接裂纹,是制造大型压力容器（特别是低温和常温球罐）、水电站压力钢管和水轮机蜗壳、高寒地区使用的大型工程机械、大跨度桥梁及海上采油平台等装备的理想用材。     

10000m^3天然气球罐用WEL—TEN610CF钢焊接冷裂纹敏感性

WEL-TEN610CF钢是日本新日铁公司生产的低裂纹敏感性高强钢,结合我国首台国产化10 000 m3天然气球罐用37 mm厚WEL-TEN610CF钢焊接性试验研究,对该钢焊接冷裂纹敏感性进行了综合评定,为其焊接工艺的制订提供了可靠的依据。     

Metallurgical failure analysis of cold cracking in a structural steel weldment: Revisiting a classic failure mechanism

Cold cracking of structural steel weldments is a well-characterized, well-documented, and well-understood failure mechanism. Extensive effort has been put forth to recognize the welding and materials selection parameters that are conducive to cold cracking; however, these engineering efforts have not fully eliminated the occurrence of such failures. This article describes cold cracking failure specifically related to the construction industry. This particular failure was successfully identified prior to final erection of the structural member, and the weld was successfully reworked. These actions potentially prevented a serious catastrophic event that could have occurred have occurred either later in the construction process or possibly during the use of the building. Individual welding parameters, such as electrode/wire selection, joint design, and pre/postheating, played a role in the failure, and a number of human factors relating to the actual fabrication practices also contributed to the failure process.     

管环缝射线一次透照长度及分段次数的计算

介绍了管环缝射线透照方式，以及环缝单壁外透法和环缝双壁单影法100％射线透照检查一次透照长度及分段次数的计算。     

焊接箱型截面构件在不同焊缝熔深下承载力性能试验研究

为了有效改善大跨度桥梁中管翼缘焊接箱型截面构件的耐久性的问题,提出采用耐候钢代替普通钢的管翼缘箱型截面梁。同时,为了研究耐候钢管翼缘焊接箱型截面构件填充混凝土后在全熔透和部分熔透条件下的单轴承载力性能,开展了焊接矩形截面在三种不同焊缝熔深下的耐候钢管混凝土截面轴压短柱试验研究。分别测试每个试件在单轴压力作用下的静态应变、动态应变,以及竖向位移和侧向位移。对比构件承载力的试验结果及理论分析结果,得出不同熔深下焊接箱型截面管翼缘组合构件的承载力性能。研究结果表明:1）耐候钢管翼缘焊接箱型截面构件的全熔透焊缝承载力高于部分熔透焊缝承载力。2）全熔透试件开裂时的竖向位移较部分熔透试件的位移值大,而不同熔深下构件的横向位移测点L4随轴压荷载的增大而有增加,L3测点横向位移规律不明显。3）不同耐候钢管翼缘焊接箱型截面构件横向整体受拉,局部在顶部角部位置受压。构件的混凝土内部和钢板表面应变情况复杂,规律不明显。     

真空粉末绝热低温贮罐制造的部分工艺方法

在真空粉末绝热低温贮罐的制造过程中、通过吸附器分子筛的活化、夹层真空系统的处理和充装珠光砂等工艺方法的改进,可较大地缩短产品的制造周期并提高产品的质量。     

Application of High Temperature Corrosion-Resistant Materials and Coatings Under Severe Corrosive Environment in Waste-to-Energy Boilers

Corrosion-resistant materials (CRMs) and coatings are key technologies to increase power generation efficiency and reduce maintenance in waste-to-energy (WTE) plants. Corrosion environment became severe as steam temperatures have increased. The steam condition of more than 400 °C/3.9 MPa became possible in WTE boilers by using highly durable corrosion-resistant coatings, such as thermal spray of Al/80Ni20Cr alloy, HVOF-sprayed NiCrSiB alloy, Alloy 625 weld overlay for waterwall tubes and also superheater tubes. Also, the use of 310S type stainless steels and high Cr-high Mo-Ni base and high Si-Cr-Ni-Fe alloys have progressed because of a better understanding of corrosion mechanisms. Furthermore, high durability coatings using cermet and ceramic materials were applied to high temperature superheaters. This paper describes the major developments and the application of CRMs and coating technologies in the last 30 years in WTE plants, the corrosion mechanisms of alloys, the deterioration mechanisms of spray coating layers, and future subjects for the development of corrosion-resistant materials and coatings.