Influence of Al3+ doping for V5+ on the structural,optical, thermal and electrical properties of V2-xAlxO5-δ (x=0–0.20) ceramics

This paper reports an investigation on the structure-properties correlation of trivalent metal oxide (Al₂O₃)-doped V₂O₅ ceramics synthesized by the melt-quench technique. XRD patterns confirmed a single orthorhombic V₂O₅ phase formation with increasing strain on the doping of Al₂O₃ in place of V₂O₅ in the samples estimated by Williamson-Hall analysis. FTIR and Raman investigations revealed a structural change as [VO₅] polyhedra converts into [VO₄] polyhedra on the doping of Al₂O₃ into V₂O₅. The optical band gap was found in a wide semiconductor range as confirmed by UV–visible spectroscopy analysis. The thermal and conductivity behavior of the prepared samples were studied using thermal gravimetric analysis (TGA) and impedance analyzer, respectively. All the prepared ceramics exhibit good DC conductivity (0.22–0.36 Sm^-1) at 400 ?C. These materials can be considered for intermediate temperature solid oxide fuel cell (IT-SOFC)/battery applications due to their good conductivity and good thermal stability.     

Polyaniline-based networks combined with Fe3O4 hollow spheres and carbon balls for excellent electromagnetic wave absorption

Polyaniline (PANI)-based networks combined with Fe₃O₄ hollow spheres and carbon balls (FCP) for improved electromagnetic wave (EMW) absorption were investigated using an easy-to-industrialize solvothermal and physical method. Hollow structure Fe₃O₄ spheres with a lower density than that of the common solid sphere were prepared. As a thin and light magnetic material, Fe₃O₄ hollow spheres generate magnetic loss, carbon balls and PANI networks generate dielectric loss. The magnetic and conductive parts play appropriate roles in achieving complementarity in the EMW absorption. The relatively high specific surface area introduced by PANI networks promotes interfacial polarization and further supports dielectric loss. In conclusion, the above reasons provide multiple attenuation mechanisms. Samples FCP1 (?65.109 dB, at 12.800 GHz, 1.966 mm, from 5.6 to 18.0 GHz) and FCP2 (?61.033 dB, at 8.480 GHz, 3.328 mm, from 4.3 to 18.0 GHz) demonstrated a wide bandwidth, a small thickness, a minimum reflection loss (R_L), and a low loading ratio (25%) in paraffin-based composites. Specifically, their loading ration of 25% is much lower than the loading ratio of conventional materials (usually 50% and above). In addition, the bandwidth is excessively wide, above 12 GHz, possessing good absorption performance in continuous intervals with different thicknesses. Such excellent characteristics have rarely been reported in literature.     

ACCUGRAM: A novel approach based on classification to frequency band selection for rotating machinery fault diagnosis

Frequency band selection (FBS) in rotating machinery fault diagnosis aims to recognize frequency band location including a fault transient out of a full band spectrum, and thus fault diagnosis can suppress noise influence from other frequency components. Impulsiveness and cyclostationarity have been recently recognized as two distinctive signatures of a transient. Thus, many studies have focused on developing quantification metrics of the two signatures and using them as indicators to guide FBS. However, most previous studies almost ignore another aspect of FBS, i.e. health reference, which significantly affect FBS performance. To address this issue, this paper investigates importance of a health reference and recognize it as the third critical aspect in FBS. With help of the health reference, the frequency band where the fault transient exists could be located. A novel approach based on classification is proposed to integrate all three aspects (impulsiveness, cyclostationarity, and health reference) for FBS. Classification accuracy is developed as a novel indicator to select the most sensitive frequency band for rotating machinery fault diagnosis. The proposed method (coined by accugram) has been validated on benchmark and experiment datasets. Comparison results show its effectiveness and robustness over conventional envelope analysis, the kurtogram, and the infogram.     

Optical Properties of One-dimensional Three-component Photonic Band Gap Structure

1　IntroductionMaterialswithPhotonicBandGaps (PBG’s)havebeenwidelystudiedboththeoreticallyandex perimentallyinthepastfew years[1～ 4] .Theexis tenceofgaps,which prohibitthepropagationofelectromagnetic (EM )wavesinacertainrangeoffrequencies,canhavesignificantimpactsbothinsci enceandtechnology .Manypracticalapplicationsofthesestructureshavebeensuggestedanddemon strated ,suchasPhotonicCrystal (PC)microcavi ties[5] ,infraredPC[6] ,PClens[7] ,suppressingspontaneousemission ,manipulatinglight…     

低插损窄带型10.7MHz压电陶瓷滤波器的研制

介绍了低插损窄带型10.7 MHz压电陶瓷滤波器的一种设计制作方法。结合压电陶瓷能陷模理论,通过对滤波器分割电极设计和制造工艺控制技术的研究,强调了工艺控制的重要性。产品达到日本村田同类产品水平,对国产化窄带型10.7 MHz压电陶瓷滤波器的研发和生产具有十分重要的意义。认为选用高Qm值压电陶瓷材料、分割电极和耦合电容的设计、焊接和点蜡工艺的控制等是研制低插损窄带型10.7 MHz压电陶瓷滤波器的重点。     

A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

IEEE 802.11g性能分析及应用

全面介绍IEEE802.11g标准的无线局域网,详细讲述IEEE802.11g草案标准的概念、产生背景、特点、构件及其体系结构和发展前景,探讨实现IEEE802.11gWLAN所需的关键技术及其双频多模应用方式,同时分析IEEE802.11g标准的网络性能。     

反铁磁晶体的红外频率特性

研究了红外频段非线性s偏振表面波在反铁磁晶体和电介质交界面上的频率特性，求出了非线性色散方程，揭示了非线性s偏振表面波存在一个临界频率，低于这个频率，非线性s偏振表面波的频率范围，发现功率不再是决定导波频率范围的唯一因素，两种材料的介电常数比在这里起了至关重要的作用。     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。