Dielectric performance of pyrochlore-type Bi2MgNb2-xTaxO9 ceramics: The effects of tantalum doping

The solid solutions based on the pyrochlore-type system Bi₂MgNb_2-xTa_xO₉ were formed in the compositional range х = 0–2.0 (Bi_1·6Mg_0·8Nb_1.6-tTa_tO_7.2, t = 0–1.6). The Rietveld method was used to refine the structure for Bi₂MgNb_2-xTa_xO₉ (x = 0, 1.0, 2.0). The increasing tantalum content led to the slight decrease in the cubic unit cell parameters from 10.56934 (4) Å for x = 0 and 10.54607 (3) Å for x = 2 (sp.gr. Fd-3m:2). At the same time, tantalum additions suppressed grain growth in the pyrochlore ceramics during sintering and made it possible to obtain materials with an average grain size of 1–2 μm (Bi_1·6Mg_0·8Ta_1·6O_7.2). The increase in the Ta⁵⁺ concentration led to the decrease in the dielectric permeability from 104 (Bi_1·6Mg_0·8Nb_1·6O_7.2) to 20 (Bi_1·6Mg_0·8Ta_1·6O_7.2) at room temperature, while the dielectric loss tangent remained lower than 0.002, which is due to the small grain size and the high porosity of the samples. An increase in temperature has practically no effect on the values of the dielectric permittivity in the entire frequency range. The samples have weak through conductivity. The activation energies of electrical conductivity varied in the range of 0.84–1.00 eV, and the less tantalum, the lower the activation energy. The electrical properties of the samples at 200 Hz to 1 MHz are described by the simplest parallel scheme.     

In2O3:Ga and In2O3:P-based one-electrode gas sensors: Comparative study

Gas sensing characteristics of one-electrode sensors based on the In₂O₃ ceramics doped by gallium and phosphorus have been discussed. In₂O₃-based ceramic was prepared by sol–gel technology. Ozone, CO, CH₄ and H₂ were used as tested gases. The doping concentration effect on the sensor parameters such as magnitude of response, operating temperature, response and recovery times, sensitivity to the air humidity, and selectivity have been analyzed. It was shown that In₂O₃ doping by Ga and P could be used for the sensor performance optimization. It was assumed that the appearance of the second phase (InPO₄ and Ga₂O₃) and the change of structural parameters, taking place during doping process, were the main factors controlling the change of operating characteristics in In₂O₃:P and In₂O₃:Ga-based sensors.     

Stabilization of 6H-Hexagonal SrMnO3 Polymorph by Al2O3 insertion

We demonstrate the structural evolution of polymorphic phases in Al₂O₃-inserted SrMnO₃ ceramics synthesized by solid state reaction. While the 4H-hexagonal phase is predominant in pure SrMnO₃ ceramics, a small amount of 6H-hexagonal polymorph is identified in addition to the primary 4H-hexagonal SrMnO₃ and the secondary hexagonal SrAl₂O₄ phases in the as-sintered ceramics, evidenced by x-ray diffraction and subsequent Rietveld refinement analyses. The existence of the 6H-hexagonal SrMnO₃ phase is corroborated using Raman spectroscopy. The chemical compositions and electronic structures of the Al₂O₃-inserted SrMnO₃ compounds are also examined using energy dispersive spectroscopy and x-ray photoelectron spectroscopy, respectively. The first-principles calculations reveal that there is no clear difference between the total energies of 4H- and 6H-hexagonal polymorphs regardless of the presence/absence of Sr and oxygen vacancies. Possible origins are discussed with the estimation of actual strain based on the refined lattice parameter of 6H SrMnO₃.     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.     

俄罗斯陶瓷及其金属化技术的研究

采用X射线荧光、X射线衍射、金相显微镜和扫描电镜等分析方法 ,通过对微波管陶瓷材料的理化分析 ,对俄罗斯陶瓷及其金属化技术进行了研究 ,并对化学成分和显微结构对性能的影响作了初步的讨论。     

Effects of Ca and Zr substitution upon structure and properties of Ba5LaTi3Ta7O30 low-loss dielectric ceramics

Effects of Ca and Zr substitution upon the dielectric properties of Ba₅LaTi₃Ta₇O₃₀ ceramics were investigated together with the structural characterization. All the samples of Ba₅La(Zr_xTi_1−x)₃Ta₇O₃₀ formed a filled tungsten-bronze structures, whereas the solid solution limit was determined as x=0.25 in (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀. Beyond this limit secondary phase of CaTa₂O₆ was detected and it would become the major phase for the Ca-rich compositions. The temperature coefficient of dielectric constant was improved with increasing Zr content while the dielectric constant decreased and the low dielectric loss varied little (in the order of 10⁻⁴). In the case of (Ca_xBa_1−x)₅LaTi₃Ta₇O₃₀, small temperature coefficient of dielectric constant could be obtained with increasing Ca content while the dielectric constant decreased significantly, and a small amount substitution of Ca for Ba induced decrease in dielectric loss.     

Effect of hot pressing on processing and properties of BBN ceramics

BBN (BaBi₂Nb₂O₉) is very interesting and promising lead free material with relaxor properties in capacitors, sensors and actuators.     

陶瓷减水剂、助磨剂、增强剂的发展现状、趋势及展望

阐述了陶瓷行业所用添加剂的分类，以及目前国际上主要生产陶瓷添加剂的厂家及主要产品，详细介绍了陶瓷坯体减水剂、助磨剂、增强剂的种类、应用、性能特点和它们与陶瓷材料的作用机理，并对陶瓷添加剂的发展前景进行了展望。     

Development of a Ceramic Micro Heat Exchanger – Design,Construction, and Testing

This article presents the development of a ceramic micro heat exchanger. Starting from its geometrical design, results obtained from a simplified simulation of the heat exchanger efficiency will be given. The alumina microcomponents were manufactured by a rapid prototyping process chain. Here, stereolithography was combined with a low‐pressure injection molding process for the rapid and precise manufacturing of ceramic components down to the micrometer range. A micro heat exchanger, joined from sintered components using a glass solder, was applied as a prototype and checked for its performance at a system pressure of 8 bar.