Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

嵌人式与独立存储器设计上的差异分析和研究

进入21世纪,随着集成电路的发展,SoC(System on Chip)片上系统应运而生。而作为SoC重要组成部分的嵌入式存储器,在SoC中所占的比重正逐步增加,并起着越来越重要的作用,那么嵌入式存储器与独立的存储器芯片在设计上存在着哪些差异?对此本文将以NOR型闪存为例在制造工艺的选取、衍生产品的设计、功耗与噪声、后端功能仿真、测试与修复等方面进行分析和研究。     

连续梁的简便计算

利用三转角方程，对连续梁的内力进行精确的计算，该方法简捷明了，便于应用。     

DS1620实现的X射线采集板温度自动控制

DR是目前非常先进的X射线成像技术，将其X射线采集板工作温度控制在最佳工作范围可采集更好的图像。本系统采用PC和单独控制双模块分别控制温度，利用半导体传感器DS1620进行四路温度采集，通过单片机和PC串口通信，用PC通过半导体制冷芯片来控制X射线采集板的工作温度，在通信故障时也可以通过单独控制模块来控制采集板的温度。     

工业建筑多层框架的活荷载不利布置

以设防烈度为8度的框架厂房为例，详细分析了活荷载不利布置对框架梁、柱内力的影响，得出何时需要考虑活荷载不利布置、何时不需要考虑活荷载不利布置的结论，可供工程设计参考。     

Use of radial forces for fault detection in tapping

A model-based method for fault detection in tapping based on torque and radial forces is proposed. The method allows the identification of faults typical of a tapping operation including axial misalignment, tap runout, tooth breakage both singly and together. The validation experiments have been run on aluminum 356 workpieces for different combinations of process faults. Results have shown that the model predictions are in good agreement with the experimental radial force and torque signals under various fault conditions.     

Evidence of High Vertical Wave-Number Behavior in a Continuously Stratified Reservoir: Boadella, Spain

High vertical wave-number modes clearly dominate the internal wave field during the stratification period in Boadella reservoir in northeast Spain. In this period, the extraction of hypolimnetic water, due to summer irrigation, brought the surface level down by 6 m in one month and the epilimnetic water progressively occupied the whole water column. The temperature profile, with the exception of a few meters at the surface layer, presented an almost constant temperature gradient of about 0.7°C/m. The period of the main vertical mode is 24 h with an amplitude of around 1 m. Thermistor chain records and meteorological data allow us to deduce that this mode is, at least, a third vertical mode forced by the wind, which normally has a typical periodicity of 24 h. However, when the wind changes direction from south to north, the circulation cells developed due to this forced nonstationary oscillation are destroyed. When this occurs, the Bulk Richardson number is Rib ～ 1. Similar vertical structures as a response to wind forcing should be expected in similar systems, although this has not been reported in the literature.     

HYDRODYNAMIC FORCE ON SMOOTH HORIZONTAL CYLINDER IN UNIFORM OSCILLATORY FLOW

ＨＹＤＲＯＤＹＮＡＭＩＣ　ＦＯＲＣＥ　ＯＮ　ＳＭＯＯＴＨ　ＨＯＲＩＺＯＮＴＡＬ　ＣＹＬＩＮＤＥＲ　ＩＮ　ＵＮＩＦＯＲＭ　ＯＳＣＩＬＬＡＴＯＲＹ　ＦＬＯＷＨＹＤＲＯＤＹＮＡＭＩＣＦＯＲＣＥＯＮＳＭＯＯＴＨＨＯＲＩＺＯＮＴＡＬＣＹＬＩＮＤＥＲＩＮＵＮＩＦ...     

单片机控制泄漏电流测试仪

以8031单片机为核心的泄漏电流测试仪的硬件结构和软件设计。     

数控加工的基本坐标系和对刀问题

数控加工中的对刀问题影响机械加工的各个方面。这里从介绍数控机床的基本坐标系出发，重点阐述了对刀的基本原理和方法以及常见数控机床对刀问题的处理。