Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

施工中电焊机的安全使用简述

从电焊机自身电气特点及建筑工地工作环境入手,探讨电焊机安全技术的实施方法。分析电焊机安全隐患及事故的分类以及电焊机在使用过程中产生危险的原因。介绍电焊机在安装以及作业过程中的安全措施。     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

煤矿工业场地道路照明接地系统问题探讨

文章简要介绍了煤矿工业场地的特点和低压配电系统接地方式分类,从安全性、经济性的角度分析了TN接地系统和TT接地系统在道路照明回路中的优缺点。通过对比TN-S系统与TT系统的接地故障电流差异、TN-S接地系统用于道路照明的等电位联结困难程度,总结出煤矿工业场地的道路照明配电系统适宜采用TT接地方式。并且详细阐述了TT接地系统剩余电流动作保护器保护整定方法和灵敏度校验方法,列举了煤矿工业场地道路照明选用TT系统时需要注意的中性线不可重复接地的问题。     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

DC/DC电源中的电磁干扰及其对策

概述了电磁干扰(EMI)和电磁兼容(EMC)的基本知识，对DC／DC电源中的电磁干扰进行了综合分析，并给出了各自的解决方案。     

用于磁场测量的高精度500A/30V零压开关直流稳流电源

研制了一种带有无源辅助网络的全桥移相脉宽调制零压开关(FB PSPWMZVS)高精度磁铁稳流电源,并在电磁铁磁场测量中得到应用,其电流稳定度在8h内优于±1×10-4。     

电子电路中抗EMI设计

电磁干扰(EMI)可分为传导干扰和辐射干扰,消除干扰的方法可以采用硬件方法和软件方法,硬件方法主要有屏蔽、接地、隔离和滤波等,而软件方法主要是滤波。笔者对各种方法进行总结,并指出各种方法所存在的问题以及适用场合,并对一些常用方法提出改进措施。     

一种考虑分布电容的模糊故障测距算法

提出了一种考虑分布电容的故障测距新算法。该算法基于微分方程描述的线路数学模型，利用单端信息对高压输电线路进行故障测距，保留了解微分方程算法的简单可靠、现实可行、不必考虑衰减直流分量和谐波及电网频率波动影响的特点，同时考虑过渡电阻和分布电容的影响，克服了传统解微分方程法中在经高阻接地故障时测距误差过大和忽略分布电容引起的故障定位不准确的缺点。为了检验算法的精度，进行了大量的动模实验。结果表明，算法原理正确并具有较高的测距精度。