涡轮搅拌桨反应器混合过程的数值计算

利用CFD方法计算单层涡轮反应器搅拌槽内流体混合过程的速度场和浓度场,研究物料在搅拌槽内的混合过程,以及不同监测点对混合时间的影响。结果表明,搅拌槽内物料的混合主要受槽内流体的流动形式所影响;混合时间的长短与监测点位置有关;在搅拌桨的桨叶附近进行监测所得到的混合时间较短,在液面附近进行监测所得的混合时间较长。在实际生产和试验中,应注意对监测点位置的选取。     

夯扩挤密水泥土桩用于高层建筑地基处理的尝试

水泥土桩已普遍用于多层住宅的地基处理，根据水泥土和夯扩挤密施工法的特点，在对夯扩挤密水泥土桩用于高层建筑地基处理进行研究、阐明其经济合理且安全可行的基础上，在高层住宅工程中进行了尝试，已取得令人满意的效果。     

异质谷间转移电子器件的计算机模拟

使用弛豫时间近似求出了描述两能谷间电子交换的方程。在此基础上建立了双能谷电子的连续性方程和油松方程。对具体的ＧａＡｓ／ＡｌｘＧａ１－ｘＡｓ异质谷间转移电子器件结构求解了这些方程组，得到了直流工作时器件内的电场分布、双能谷中载流子的布居以及两个能谷的电流分布。这些结果正好和常规Ｇｕｎｎ器件相反，说明了两种器件的不同工作机理。最后通过对低Ａｌ组份势垒结构的计算说明了Ｘ谷电子注入对器件工作的重要作用。     

Comparison of Displacement and Mixing Diffusers

In order to cumpare the peformance of different supply diffuers of ventilation air, the airflow passern, temperature stratifiation and contaminant dispersion in a furnitured office ventilated by three kinds of air diffuer were numerically investigated. The air diffuers studied in this paper are a quarter-cylinder displacement diffuer on the floor and mixing diffuers (linear and vortex diffuers) on the ceiling. The heat sources in the of-fice are considered to be 50% convective and 50% radiative. The k-? two-equatwn model of turbulence is employed to predict the turbulent diffusion. The results show that the displacement diffuser provides a rather uniform flow field with low velocify in most areas, and the vertical temperature difference from floor to ceiling is as high as 6 K. With the linear diffuser, the air velociry is high, and the temperature is uniform both horizontally and vertically. The air velocity generated by the vortex diffuser is moderate. The distributions of the temperature and the contaminant are rather uniform.     

Mixing Center of a Channel

For longitudinally uniform stretches of waterways there is a mixing center for the across-channel location of a steady point source in steady flow, such that complete mixing is achieved as soon as possible and there is no concentration overshoot at either of the two shorelines. A mathematical definition of the mixing center is the zero of the first oscillatory cross-channel diffusion mode. With the shorelines plus four interior data points across the channel, the starting estimate for the mixing center suffices to keep peak shoreline concentrations to within 6% of optimal. For comparison, a source at mid flow gives 18% shoreline concentration overshoot in the test case. Should very high precision be required, the Appendix gives an iterative construction that converges to the first oscillatory diffusion mode.     

光电摆角动态测量原理及其测量系统

本文阐述了用于测量物体摆角及摆心浮动量的光电动态实时测量原理,以及根据此原理研制的光电导弹喷管摆角动态测量系统。     

烷基化原料预加氢工艺应用分析

由于来自催化裂化装置的烷基化原料中所含有的丁二烯在烷基化反应中可生成重质油,使产品干点上升,辛烷值下降,并使酸耗增加.针对这种状况,齐鲁石化公司研究院和胜利炼油厂联合开发了QSH-01烷基化原料预加氢催化剂及其相应的工艺技术,来脱除原料中丁二烯.笔者对该工艺技术及其应用作了阐述,并对该技术的应用前景作出分析.     

Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.     

Diffusion Bonded EDM Electrode with Micro Holes for Jetting Dielectric Liquid

This paper describes improvement of machining characteristics of electrical discharge machining of deep slots using a tool electrode which has micro holes for jetting dielectric liquid over the working surface. The tool electrode was made by the diffusion bonding of two copper plates, over an interface on which micro grooves for jetting the dielectric fluid were formed using electrolyte jet machining. In conventional machining, it is difficult to drill micro holes at the end of a slim electrode and circulate the dielectric fluid from the other end. Hence a solid tool electrode is used and periodically lifted up during machining to flush debris particles out of the discharge gap. Use of the newly developed tool electrode was found to shorten the processing time and improve machining accuracy significantly compared with the conventional solid tool electrode. Since the holes are micro, the outlet shapes are not replicated onto the bottom surface of the slot machined.