谐波齿轮机构在商业表格印刷机中的应用

从商业表格印刷机特殊要求出发，以某一具体机型的传动系统为例，提出采用谐波齿轮机构解决纵向套准的问题。并且分析研究了谐波齿轮机构的工作原理及其在商业表格印刷机中的使用。     

乘性和加性噪声中谐波恢复的循环统计量方法

本文从循环平衡的观点出发来研究乘性和加性噪声中的谐波恢复问题.首先，在一定条件下建立了一般复过程的有限长付里叶变换的大样本性质．然后，得到了任意阶循环矩的样本估计关于循环频率的一致收敛速度．对于乘性和加性噪声中的谐波信号，建立了一、二、三阶循环矩样本估计的统计性质．在此基础上，分别提出了基于不同阶循环矩的谐波分最个数和频率的估计方法，并得到了估计的强相容性质和强收敛速度，最后给出了模拟实验结果．     

SECANT-FUZZY LINEAR REGRESSION METHOD FOR HARMONIC COMPONENTS ESTIMATION IN A POWER SYSTEM

In order to avoid unnecessary damage of electrical equipments and installations,high quality power should be delivered to the end user and strict control on frequency should be made, Therefore, it is important to estimate the power system's harmonic components with higher accuracy. This paper presents a new approach for estimating harmonic component in a power system using secant - fuzzy linear regression method. In this approach the non - sinusoidal voltage or current waveform is written as I linear function. The coefficient of this function is assumed to be fuzzy number with a membership function that has center and spread value. The time dependent quantity is written as Taylor series with two different time dependent quantities. The objective is to use the sample obtained from the transmission line to find the power system harmonic components and frequencies. We used an experimental voltage signal from a sub power station as a numerical test.     

CAD OF MILLIMETER WAVE OSCILLATORS WITH THE FDHB TECHNIQUE

In this paper the modelling, analysis and optimization of millimeter wave oscillatorsare investigated by using the a frequency-domain harmonic balance technique (FDHB), where theexternal-circuit impedances looking outside from the active device are calculated with a combinedtechnique of modes expansion, Galerkin, and collocation methods. The optimization results arein agreement with the experimental ones, which show the reliability of the presented model andoptimization.     

Accurate higher-order analytical approximate solutions to nonconservative nonlinear oscillators and application to van der Pol damped oscillators

In general, this paper deals with general nonlinear oscillations of a nonconservative and single degree-of-freedom system with odd nonlinearity and, in particular, it presents accurate higher-order analytical approximate solutions to van der Pol damped nonlinear oscillators having odd nonlinearity and the Rayleigh equation. By combining the linearization of the governing equation with harmonic balancing and the method of averaging, we establish accurate analytical approximate solutions for the general weakly damped nonlinear systems. Unlike the classical harmonic balance method, simple linear algebraic equations instead of nonlinear algebraic equations are obtained upon linearization prior to harmonic balancing. The combination of these two methods results in very accurate transient response of the periodic solution. In addition and for the first time, this paper also presents a method for deducing fourth-, fifth- and higher-order linearized governing equations from the lower-order equations without the requirement of formulating the problem from the first principle. Three examples including the van der Pol damped nonlinear oscillator are presented to illustrate the excellent agreement with approximate solution using the exact frequency.     

BKX-Ⅰ型并联机床的谐响应分析

应用有限元分析软件(ANSYS),对BKXⅠ型并联机床进行谐响应分析,分别得到了机床各节点沿机床的虚拟轴X、Y和Z向的位移谐响应曲线。在此基础上,还分析了该机床的谐响应规律,并明确了谐响应的特点,为改善此类机床的动态特性提供了一定的参考依据。     

低压补偿滤波装置的应用分析

用实例对比了低压补偿滤波装置与传统的无功补偿装置对工业用户无功补偿的作用和安装，运行、维护情况，阐明了低压补偿滤波装置是一种兼顾了补偿和滤波功能，具有较高的技术性和经济性的无功补偿和谐波滤波装置。     

调制式光纤甲烷气体传感器的研究

利用Fabry-Perot腔的选频特性，考虑与光纤的低损耗窗口相一致和价格等因素，以价廉的1300nm波段的LED作为光源，实现了PZT对Fabry-Perot腔的正弦调制；对甲烷气体浓度进行谐波检测，检测灵敏度可达10ppm。研究表明，该传感器灵敏度和稳定性大大提高。     

新型硬齿面环面蜗杆传动研究

采用精确磨削TI蜗杆的砂轮，用类似直廓环面蜗杆或平面包络环面蜗杆的磨削方法加工环面蜗杆，使该蜗杆和齿面形状与砂轮曲面相同的蜗轮相配合，形成一种新型蜗杆传动，给出了这种传动蜗杆副齿面的数学模型，并通过计算机仿真得出了这种传动蜗轮齿面上接触线的形状及分布特征，初步分析了其啮合特点。     

A helical drive in-pipe robot based on compound planetary gearing

The modern society is fuelled by very comprehensive grids of gas and liquid pipelines. In recent years, various in-pipe robots have been developed for inspection and maintenance tasks inside such pipes. In this paper, a novel in-pipe robot is proposed and developed for gas/oil well interventions at thousands of meters downhole. Due to the nature of such intervention, in-pipe robot design must be capable of carrying a very large payload, as large as 2500?N inside a pipe with diameter as small as 54?mm. The proposed design concept is based on a compound planetary gearing system. One of the major novelties of this design is the use of pipe wall as a ring gear for one stage of the compound planetary gear system; the other novelty is the generation of helical angle when the planetary gears are expanded to press on the pipe wall. The proposed concept is compact, efficient, and has never been reported before. In this paper, the helical angle, the velocity, and load capability of the proposed system will be analyzed. The load transportation capability of the proposed robot is also measured based on an experiment. Initial data have shown great potential in carrying large payloads.