Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

黑匣子高温测试仪的开发

采用物质的相变吸热原理，可以将高温环境传人保温箱的热量重新排回至高温环境，有效地提高了保温箱的抗高温能力，并对保温箱的隔热性能做了简单的理论推算和测温反向试验。温度测试仪选用超低功耗CPU，具有体积小、耗电少的优点，使黑匣子高温测试仪在运行过程中具有很好的安全可靠性。     

基于电源、地桥的电源网络布线后优化

随着集成电路规模的不断增大,电源网络的重要性日趋显著,电源网络的分布直接影响芯片的电压降(IR-drop)。一种布线后通过在空闲处插入电源桥和地桥的方法,可以在不增加芯片面积的情况下,改善IR-drop效应。实验结果表明在芯片布局利用率不高的情况下(70~75%),该方法可以使IR-drop得到明显的优化。     

SCB火工品的研究与发展

文章评述了半导体桥火工品问世以来的研究成果与发展趋势。主要内容有半导体桥作用机理、半导体桥的结构与封装、半导体桥火工品的特点、半导体桥火工品的应用、半导体桥火工品的研究和发展趋势。     

多跨简支曲线轨道折线梁桥空间振动分析模型

提出了一种多跨简支曲线轨道折线梁桥的空间振动分析模型,采用20自由度的梁段单元,可方便考虑T型梁横向与竖向弯曲、自由扭转、约束扭转等变形,选取正交流动坐标,建立了曲线轨道折线梁桥的动力特性矩阵,特别适用于曲线轨道折线梁桥与列车的空间振动分析。在实例研究中,计算了提速列车通过32m曲线轨道折线梁桥时的空间振动响应,并检算该桥是否具有足够的刚度及良好的运营平稳性,可供有关部门参考。     

300km/h高速铁路PC槽型梁动力试验研究

介绍北方交通大学与比利时鲁汶大学、布鲁塞尔自由大学、比利时铁路公司合作,在巴黎至布鲁塞尔之间高速铁路线上的Antoing大桥进行的二次高速铁路桥梁动力试验。试验桥梁由跨度50m的多跨预应力混凝土简支槽型梁构成,试验中列车速度达265-310km/h。通过现场试验和实验结果分析,得到了桥梁的频率、振型、阻尼等自振特性,以及桥梁在高速列车作用下的动挠度、梁和桥墩的横向和竖向加速度、橡胶支座的相对位移、梁体的动应变等动力响应特性。试验经验和测试结果对于充实高速铁路桥梁动力分析理论、改进数值分析模型、验证计算结果、提高高速铁路桥梁的动力设计水平、保证行车安全,具有重要的意义。     

ㄇ形梁剪力滞效应的解析解

精确分析ㄇ形梁在纵横向荷载共同作用下,其横断面上正应力分布规律对于计算其有效宽度有重要意义,应用力法原理,先将ㄇ形梁和翼板截开成矩形截面梁和平面应力板,在截面上代之以赘余的分布剪力,对于平面应力板,通过利用板变形的对称性来简化其边界条件,然后假设一个满足板的控制方程的Airy应力函数求得板的应力和位移,再利用Timoshenko梁理论求得梁的挠度和转角,根据截面上梁与板的纵向位移相等的变形协调条件便可最终确定截面上的分布剪力,给出的数值算例验证了方法的有效性,并与铜陵长江公路大桥主梁的模型有限元结果和试验结果作了对比,解析解法还可用来检验其他各种数值计算方法的精度,并可推广到其他多跨薄壁结构梁桥的膜应力分析中。     

基于数字机顶盒的电子选单的设计和实现

基于CATV和PSTN的VOD多媒体数字机顶盒，提出了几种实现双向通信以完成电子节目指南的设计方案，对各种方案的优缺点进行了详细的讨论，并介绍了所采用方案的实现方法。     

交通平衡分配下的公路桥收费策略

假定一个城市被一条河流分为两部分（如我国的武汉，重庆等市），河上至少架设了两座公路桥梁，本文研究在交通平衡状态下，怎样制定车辆过桥梁的收费水平，使获得的总收入最大，乘客的总行驶时间最少，对多车种问题，研究了等价的数学模型和算法。还对一个含两座桥梁与三种车型的简单算例，进行了计算与分析。     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.