LBM investigation of a Cu-water nanofluid over various configurations of pipes in the mixed convection flow

Increasing the heat capacity of heat exchangers is a crucial need for modern devices. The thermal conductivity of the usual fluids and the Nusselt (Nu) number of flows containing such fluids are two bottlenecks in the way of increasing heat delivery in the heat exchangers. For this reason, nanofluids have been introduced. The effect of utilizing a Cu-water nanofluid as a coolant of two hot pipes in a square cavity is investigated numerically with a two-component lattice Boltzmann method. The volume fraction of nanoparticles is assumed to be constant (0.03) while the Richardson (Ri) number varies from 0.02 to 20. Results show that the effectiveness of nanoparticles is better observed in the natural convection mode. However, sedimentation is also very probable at high Ri numbers, which significantly reduces the effectiveness of the nanoparticles. Configurations which produce a natural convection stream similar to the forced convection one as well as the configurations with high spacing and hence, low heat stream interactions, are the best choices for a uniform heat rate from the pipes.     

Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

Exergoeconomic performances of the desiccant-evaporative air-conditioning system at different regeneration and reference temperatures

This paper presented the exergoeconomic evaluation of the developed desiccant-evaporative air-conditioning system. The developed system was evaluated based on the steady-state conditions at different regeneration and reference temperatures. The exergoeconomic evaluation method was implemented to the system components and the whole system to evaluate the exergy efficiency, exergy destruction ratios, cost rates, relative cost differences and exergoeconomic factors. The regeneration and reference temperatures affected the exergy efficiencies, exergy destruction ratios, cost rates, relative cost differences and exergoeconomic factors. The desiccant wheel, heating coil and evaporative cooler had a high cost rate (investment cost, operation and maintenance cost, and exergy destruction cost). The exit air fan, outdoor air fan and evaporative cooler had a high relative cost difference. The exit air fan, outdoor air fan and secondary heat exchanger had a high exergoeconomic factor. Replacement of the desiccant wheel with a higher dehumidification performance could decrease the high cost rate. A higher efficiency evaporative cooler and heating coil were needed. Cheaper air fans (outdoor air fans and exit air fans) were needed.     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

聚氨酯胶粘剂在苯板夹心板生产中的应用

简要介绍了聚氨酯胶粘剂在彩钢板／聚苯乙烯夹心板生产中的应用、采用双组分无溶剂发泡型聚氨酯胶粘剂生产夹心板的工艺。对胶粘剂配制中原料的选择和工艺参数的确定进行了讨论。采用由聚醚、水、催化剂等配成的混合物为A组分，多异氰酸酯作为B组分，制成的发泡型聚氨酯胶粘剂具有固化速度快、成本低、实用效果好等优点，滴胶和抹胶的施工方法工艺简单，可满足夹心板生产的需要。     

激光抛光技术的发展与展望

介绍激光抛光技术的发展历史,阐明激光抛光的应用现状及未来的发展前景,论述了激光抛光的工艺特点和作用机理,将激光抛光技术与其它抛光技术进行了全面的对比,指出激光抛光的优势及其存在的问题。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

冷媒充填机的PLC控制

介绍了冷媒充填机控制系统的组成和工作原理，着重叙述了西门子S7－200可编程控制器与触摸屏结合的控制方式，使系统的性能得到较大的提高。     

Fringe probing of an evaporating microdroplet on a hot surface

The phenomenon of droplets impacting and evaporating on a hot surface is of interest in many areas of engineering. Quantitative measurement of these processes provides great help to reveal the physics behind. A novel technique was developed to quantitatively measure the volume evolution and contact diameter of an evaporating microdroplet on a hot surface utilizing interference fringe scattering method. In this method, fine fringes produced by the interference of two coherent laser beams was scattered by the droplet and projected onto a screen. The profile and volume of the droplet can be derived from the spatial fringe spacing on the screen. The number of total fringes measurable on the screen was used to determine the instantaneous contact diameter of the microdroplet. Validation experiments demonstrated that the measurement errors are less than ±5% and ±1% for microdroplet volume and contact diameter, respectively. By using this method, the dynamic of droplet impingement, evaporation and boiling using ethanol, pure water and water solution of a surfactant (sodium dodecyl sulfate) with impact velocity of 7.5 m/s and diameters ranged from 0.19 to 0.46 mm were investigated.