Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

沉管隧道水下最终接头施工技术初探

简述了沉管隧道水下最终接头施工技术的应用现状，结合具体隧道工程实例，从外模工程、混凝土结构两方面介绍了最终接头施工技术，表明了该技术具有运用价值。     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法

提出了一种新的计算弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法，它是一种时域复模态分析方法。利用此方法获得了弹性-粘弹性复合结构在白噪声、滤过白噪声等典型平稳随机激励下随机响应的各阶谱矩的解析表达式，分析了粘弹性对各阶谱矩的影响。此计算方法简便、易用，无论单自由度或多自由度系统均适用，为进一步研究弹性-粘弹性复合结构在随机激励下的可靠性打下良好基础。     

规整填料和新型塔板设计参数选取的质疑及分析

笔者指出了目前规整填料和新型塔板设计计算中若干尚未完全解决的、有争议或值得进一步完善的设计参数。如:规整填料的每米理论板数、最小液体喷淋密度、最小气体空塔动能因子、新型塔板开孔率等,并提出了具体的设计方案供与同行切磋。     

组合结构体的控制爆破拆除

根据待拆构筑物的结构特点和周围环境，分析论述构件倒塌的可能性。因地制宜选择，制定出合理的爆破方案。并通过对爆破参数，起爆网络，安全防护等进行精心设计和施工，拆除爆破达到了预期的效果。     

30.4 nm光电成像系统分辨率的初步实验研究

本文基于微通道板MCP(Microchannel Plate)探测器件设计一套成像系统，用于对波长为30．4nm的极紫外EUV(Extreme Ultraviolet)光进行成像．结果获得了一宽度为3mm的狭缝的像，实验测得490μm的成像系统的空间分辨率，并分析了影响系统分辨率的各种因素及为提高系统分辨率所应采取的措施．