Experimental study of crystal anisotropy based on ultra-precision cylindrical turning of single-crystal calcium fluoride

To realize ultimately efficient signal processing, it is necessary to replace electrical signal processing circuits with optical ones. The optical micro-resonator, which localizes light at a certain spot, is an essential component in optical signal processing. Single-crystal calcium fluoride (CaF₂) is the most suitable material for a highly efficient optical micro-resonator. The CaF₂ resonator can only be manufactured by ultra-precision machining processes, because its crystal anisotropy does not allow the application of chemical etching. However, the optical micro-resonator's performance depends definitely on the surface integrity.This study investigated the relationship between surface quality after ultra-precision machining and crystal anisotropy. Firstly, crack initiation was investigated on the (1 0 0), (1 1 0), and (1 1 1) planes using the micro-Vickers hardness test. Secondly, brittle-ductile transition was investigated by orthogonal cutting tests. Finally, cutting performance of cylindrical turning was evaluated, which could be a suitable method for manufacturing the CaF₂ resonator. The most difficult point in cylindrical turning of CaF₂ is that the crystalline plane and cutting direction vary continuously. In order to manufacture the CaF₂ optical micro-resonator more efficiently, analysis was conducted on crack initiation and surface quality of all crystallographic orientations from the perspective of slip system and cleavage.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

恢复邢台百泉泉水流量可行性研究

通过百泉泉区天然状态与超采状态下的水环境对比分析,并对岩溶水补给量和开采量进行计算,阐述恢复邢台百泉泉水流量的可行性,随着“引朱济邢”和“南水北调”供水工程的实施,邢台百泉水生态环境的恢复将变为现实。     

机械-射流破岩耦合特性研究

在现代旋转钻井破碎井底岩石中仍是以机械破岩为主，理论与实践证明，射流辅助破岩是提高钻井破岩效率的重要途径，但它们的耦合特性研究极少。文章基于渗流场与应力场的耦合理论分析，进行了机械与射流破岩耦合特性的实验研究。结果表明：射流压力和水楔作用对岩石渗流场、应力场具有重要作用，耦合作用比非耦合作用的破岩效率有较大幅度的提高。在实验条件下，砂岩的耦合作用提高破岩效率40％左右，灰岩的耦合作用提高破岩效率20％左右。     

水量还原方法及合理性检查

文中详细地阐述了取河水、井水、水库水、跨流城引(排)水等不同情况进行还原的具体方法步骤。并对水量还原成果提出合理性检查措施。     

基于MODBUS协议的激光雕刻切割系统HMI人机交互设备

近年来,国内激光雕刻切割控制器技术发展迅速,基于PC的传统控制器已相当成熟.为了显著提高工业生产效率,适应工业生产规模扩张的需要以及工业对系统稳定性要求的提高,目前国内几家专业运动控制器厂家已经实现了激光雕刻切割控制器的完全脱机运行.本文针对脱机控制器的需要设计一款人机交互设备,该设备采用AT89C55WD单片机为主控制器,采用标准的MODBUS协议实现HMI与脱机控制器的可靠通讯.     

Classification of the Uncertainty of Measurements

A discussion is given of questions arising when classifying uncertainties from the point of view of the structure of the measurement process.     

双室充氮包装机的技术改进

分析了原机型的性能特点和不足之处,介绍了改进方案。