Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

JETS,PLUMES AND BUOYANT JETS IN STATIC ENVIRONMENT

Turbulence represents an essential aspect in atmospheric and oceanic circulations.In particu-lar,it is a preponderant factor in the dispersion of pollutants of artificial or natural origin.Thevertical turbulent jets,plumes and buoyant jets discharging into static environment is one of themost important and basic flow patterns related with the environment pollution.These flows havenumerous important applications,for example,thrust augmentors,waste disposal plumes fromstacks and combustion systems,and significant problems of turbulent diffusion.     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

钨铜合金药型罩及其性能

钨铜合金药型罩的应用可以提高射流对均质钢靶的侵彻能力.这一提高得益于射流密度的提高以及断裂时间的延长. 本文对钨铜合金射流及其断裂形态通过X光照像进行了研究.它的旋转效应及其炸高特性也进行了实验研究. 钨铜合金药型罩的威力实验在φ30 mm的破甲弹上进行.在相同装药条件下与紫铜罩相比,威力提高20～30%.     

SISAK快速化学分离装置的建立

SISAK(Short-lived Isotopes Studies by the AKUFVE technique)技术是目前使用最广泛的快速化学分离方法之一,主要应用在短寿命核素的分离和鉴别、超重元素的人工合成以及化学性质研究等方面的工作中.本文简单地叙述了SISAK技术的流程、原理和发展现状,介绍了自行建立的国内第一套基于SISAK技术的快速化学分离装置,并通过从裂变产物中分离短寿命核素这一实例验证了SISAK技术在快速化学分离中的优越性.     

热流体喷射变形机理与喷嘴结构

高速短程纺技术能生产三维卷曲短纤维,该技术的关键之一是热流体喷射装置。本文介绍了热流体喷射装置的演变与特点及它的加工机理和某些已应用的实际装置。     

影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

FORMATION AND FLOW OF GAS BUBBLES IN A PRESSURIZED BUBBLE COLUMN WITH A SINGLE ORIFICE OR NOZZLE GAS DISTRIBUTOR

The characteristics of gas bubbles in a 5 cm diameter bubble column equipped with a single orifice of 1,3 or 5 mm diameter were investigated under system pressure of 0.1-15 MPa. The formation of gas bubbles was strongly affected by the system pressure. Under high pressures a dispersed gas jet was formed at gas velocities where spherical gas bubbles would have been formed at atmospheric pressure. The critical gas velocity between the bubbling regime and the jetting regime was correlated with the liquid phase Weber number and the gas phase Reynolds number based on the gas velocity at the orifice. Bubble size and gas holdup in the main part of the bubble column were also affected by the bubble formation pattern at the distributor     

浅谈玻璃钢的加工

本文在实际研究和应用的基础上，对玻璃钢的传统加工方法和特种加工方法，如激光切割、纯水射流切割和磨料水射流切割作了简要论述。