全文获取类型
收费全文 | 31篇 |
免费 | 1篇 |
国内免费 | 16篇 |
专业分类
综合类 | 4篇 |
金属工艺 | 22篇 |
机械仪表 | 3篇 |
矿业工程 | 6篇 |
水利工程 | 3篇 |
无线电 | 3篇 |
一般工业技术 | 1篇 |
冶金工业 | 4篇 |
自动化技术 | 2篇 |
出版年
2021年 | 1篇 |
2020年 | 1篇 |
2018年 | 1篇 |
2016年 | 1篇 |
2012年 | 3篇 |
2011年 | 1篇 |
2007年 | 4篇 |
2006年 | 4篇 |
2005年 | 2篇 |
2004年 | 1篇 |
2003年 | 3篇 |
2002年 | 1篇 |
2001年 | 1篇 |
2000年 | 1篇 |
1999年 | 1篇 |
1998年 | 4篇 |
1997年 | 2篇 |
1996年 | 4篇 |
1995年 | 1篇 |
1994年 | 2篇 |
1993年 | 3篇 |
1992年 | 1篇 |
1991年 | 2篇 |
1990年 | 3篇 |
排序方式: 共有48条查询结果,搜索用时 15 毫秒
1.
Cu—Zn—Al合金贝氏体的初生态及三维台阶 总被引:6,自引:1,他引:6
利用透射电镜研究了Cu—25.9Zn—3.75Al(wt-%)合金的贝氏体相变机制结果表明,贝氏体α_1在形成初期内部没有层错,早期典型形态为一侧比较平直,另一侧则存在三维巨型台阶,台阶宽面与贝氏体惯习面平行,其高度和间距分别约为10—40和50—230nm,台阶是可动的,贝氏体通过台阶的移动而增厚 相似文献
2.
3.
4.
岩壁式吊车梁是一种新型结构形式,目前尚无规范可循。关口水电站地下厂房岩壁式吊车梁的设计,采用平面力系平衡的方法来分析梁的稳定,其中壁座倾角、锚杆参数选取是岩壁式吊车梁设计的关键。对中小型水电站来讲,按照施工技术要求:把好施工质量关,是岩壁式吊车梁成败的关键。 相似文献
5.
6.
The unit cell of lanthanum chromate was constructed by calculating equivalent points. By means of calculation of the hole octahedrally surrounded by O^2- ions, it was considered that the sintered property of lanthanu,n chromate and the stability of Cr - O octahedron might be promoted by mixing a little Ca^2 ions. The growth mechanism was discussed in terms of structural ledge observed by SEM, the surfaces of the structural ledges parallel to (001), (010) and (110)planes, respectively. The misfit between (110) and (001) planes is only 0.0021 on common atomic plane, and the interconnection of the structured ledge may occur during crystal growth. 相似文献
7.
Oblack[1]suggestedthatthebainiticferritewasconstitutedbysubunits.Theexistenceofsubunitswasfoundandthesubunitswerethoughttobetransformationunitsofbainite[2,3].Butthereiscontroversyaboutthenatureofthetransformationunits[4,5].Thebainiticledgegrowthmechanismwasp… 相似文献
8.
基于实例推理的冲压模结构设计的框架知识表示 总被引:2,自引:0,他引:2
将CBR的设计思想引入冲压模具的结构设计中。分析比较了知识工程中的知识表示方法,着重介绍了框架表示方法的特点和一般形式。在分析冲压模具典型结构的基础上根据冲压模具的结构特点,提出用框架作为冲压模具结构设计的知识表示手段,导出了冲压模具典型结构的框架表示。 相似文献
9.
铝电解槽炉膛内形的规整与否严重影响着电流效率,而铝电解槽的炉膛内形与电解质的过热度有很大的关系。本文通过现场测试电解温度和炉帮厚度,实验室测定电解质初晶温度的方法,考察了电解质的过热度以及过热度与炉帮厚度之间的关系。通过研究发现,过热度低于12℃时,电解槽可形成良好炉帮。 相似文献
10.