Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

规整填料和新型塔板设计参数选取的质疑及分析

笔者指出了目前规整填料和新型塔板设计计算中若干尚未完全解决的、有争议或值得进一步完善的设计参数。如:规整填料的每米理论板数、最小液体喷淋密度、最小气体空塔动能因子、新型塔板开孔率等,并提出了具体的设计方案供与同行切磋。     

多孔板体结构足尺性能分析及材料基本要求

本文就利用诸如蛋白石这样的疏松多孔矿料同灰土构成的混合料，在路面结构中表现出的独特有效的抗冻作用机理作了深入分析，并结合足尺试验数据加以验证。阐述了所谓多孔板体结构的概念、机制和材料组成要求。     

消力池底板块的失稳破坏机理及其防护措施

本文根据国内外一些高坝消力池和水垫塘失事破坏的调查资料，说明了脉动压力在引起破坏中的作用。从理论上分析了脉动压力的基本特征及其分布规律、板块上脉动上举力的产生机理，论证了脉动上举力是导致消力池底板揭底破坏的主要原因。论述了合理设置止水设施、排水设施以及锚固措施等对防止破坏的效果，讨论了计入脉动荷载的底板块稳定性设计准则，提供了消力池底板块的设计和防护参数。     

论剪切质量的提高

通过对飞剪剪切长度，精度，剪刃间隙和压板机构等参数的优化，来提高钢板的剪切质量。     

NOPD技术在板结构声辐射控制中的实验研究

本文应用NOPD技术设计了一种复合多层板，按照四边固定薄板结构的模态振型，对不同的NOPD填充形式，进行声学实验，来评价不同填充形式在降低板类结构声辐射方面的效果，分析了该类板结构声振耦合的关系并验证了NOPD技术对声辐射控制的作用。     

裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。