不同段数爆破地震波的反应谱分析

为了研究段数对反应谱特性的影响,基于某石方控制爆破工程爆破振动实测数据,对不同段数爆破振动信号进行了反应谱分析。首先,利用实测的爆破振动速度信号采用直接微分法获得了加速度信号,并利用EEMD分解对加速度信号进行低通滤波去噪处理,获得了准确清晰的加速度曲线。然后,利用精确法求得了不同段数下爆破振动信号的速度反应谱和标准速度反应谱。分析结果表明:不同段数的爆破振动质点峰值速度与速度反应谱的峰值速度并不存在对应关系,因此分段数的选择应综合考虑结构对爆破振动的动态响应。     

立柱加固型框架大楼的爆破拆除

采用定向控制爆破技术拆除立柱加固型7层框架大楼。为了彻底炸毁加固立柱,确保大楼顺利定向倾倒,通过多次爆破试验确定了炸药单耗、布孔参数和装药结构。为了控制大楼塌落时的触地震动,采取了秒差分区爆破、空中解体、铺垫缓冲层和开挖减震沟等技术措施。爆破过程中进行了震动监测。此外还介绍了起爆顺序、安全防护措施及爆破结果。     

Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

Upscaled DEM-CFD model for vibrated fluidized bed based on particle-scale similarities

Simulation based on discrete element method (DEM) coupled with computational fluid dynamics (CFD), coupled DEM-CFD, is a powerful tool for investigating the details of dense particle–fluid interaction problems such as in fluidized beds and pneumatic conveyers. The addition of a mechanical vibration to a system can drastically alter the particle and fluid flows; however, their detailed mechanisms are not well understood. In this study, a DEM-CFD model based on a non-inertial frame of reference is developed to achieve a better understanding of the influence of vibration in a vibrated fluidized bed. Because the high computational cost of DEM-CFD calculations is still a major problem, an upscaled coarse-graining model is also employed. To realize similar behaviors with enlarged model particles, non-dimensional parameters at the particle scale were deduced from the governing equations. The suitability and limitations of the proposed model were examined for a density segregation problem of a binary system. To reduce the computational costs, we show that the ratio between the bed width and model particle size can be reduced to a minimum value of 100; to obtain similar segregation behaviors, the ratio between the bed height and model particle size is considered unchanged.     

An experiential account of phantom vibration syndrome

A small handful of recent studies have addressed a phenomenon known as “phantom vibration syndrome”. This refers to when phone users perceive their device to vibrate, indicating that a call or text is incoming, when in fact the phone did not vibrate at all. Though these studies show that most users do not find phantom vibration hallucinations to be very bothersome, they also find that a large majority of users experience this phenomenon. This paper explores what the striking prevalence of phantom vibration syndrome means for our contemporary relationships with technology. I begin with a review of the theories purporting to explain these data, which largely rely on particular understandings of the brain. Next I develop an alternative theory of phantom vibration syndrome based on insights from the philosophical tradition of phenomenology. This account considers the ways users develop bodily and perceptual habits regarding how the phone is understood and used. By critically contrasting these different theories, we can refine our questions about what the high prevalence of phantom vibration syndrome implies about our contemporary technological situation.     

Studying local liquid velocity in liquid–solid packed bed using the newly developed X-ray DIR technique

Combination of X-ray Digital Industrial Radiography (DIR) and Particle Tracking Velocimetry (PTV) techniques for local liquid velocity measurement (V_LL) has been newly developed and successfully applied for trickle bed reactor (TBR). The technique was validated against newly developed fiber optical probe technique. This work attempts to highlight the applicability of this newly developed technique on a liquid–solid packed bed reactor. In this work, liquid was represented by water and solids were represented by EPS beads. The EPS beads were chosen because of its low density property. Three superficial liquid velocities (V_SL) were applied to the system. The experiment was replicated four times. The digital industrial radiography (DIR) consists of a complementary metal oxide semiconductor (CMOS) digital detector and X-ray source. Results of this work suggest that the technique has been successfully applied and comparable with previous work that has been done in the literature. It also suggests that there will be a maximum measurable interstitial liquid velocity when it travel inside the packed bed. The measured V_LL can have a maximum range that is between 4 and 4.7 times that of its V_SL. For V_SL=0.42±±2%, the V_LL-Max is in between 1.7 cm/s and 1.9 cm/s, V_SL=0.84±±2%, the V_LL-Max is in between 3.6 cm/s and 4.0 cm/s, and for V_SL=1.11±±2%, the V_LL-Max is in between 4.3 cm/s and 4.8 cm/s.     

Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

Additive manufacturing of bipolar plates for hydrogen production in proton exchange membrane water electrolysis cells

Water electrolysis is a process that can produce hydrogen in a clean way when renewable energy sources are used. This allows managing large renewable surpluses and transferring this energy to other sectors, such as industry or transport. Among the electrolytic technologies to produce hydrogen, proton exchange membrane (PEM) electrolysis is a promising alternative. One of the main components of PEM electrolysis cells are the bipolar plates, which are machined with a series of flow distribution channels, largely responsible for their performance and durability. In this work, AISI 316L stainless steel bipolar plates have been built by additive manufacturing (AM), using laser powder bed fusion (PBF-L) technology. These bipolar plates were subjected to ex-situ corrosion tests and assembled in an electrolysis cell to evaluate the polarization curve. Furthermore, the obtained results were compared with bipolar plates manufactured by conventional machining processes (MEC). The obtained experimental results are very similar for both manufacturing methods. This demonstrates the viability of the PBF-L technology to produce metal bipolar plates for PEM electrolyzers and opens the possibilities to design new and more complex flow distribution channels and to test these designs in initial phases before scaling them to larger surfaces.     

磁流变阻尼器抑制转子系统振动试验

针对大型旋转机械通过临界转速时振动过大及运行中故障频发等问题,搭建转子试验台,模拟启停机过程和碰摩、不对中故障。不改变原有支撑形式,安装自主设计的磁流变阻尼器,在不停机的情况下,试验研究阻尼器抑制转子通过临界转速时振动过大及各类故障振动。试验结果表明,阻尼器可以有效抑制转子系统临界转速附近的振动,降幅在60%以上;转子发生碰摩或不对中故障时,阻尼器可以降低其高倍频振动。     

Development and monitoring of an integrated bioprocess for production of a potential malaria vaccine with Pichia pastoris

An engineered variant of the yeast Pichia pastoris was used to produce the potential malaria vaccine D1M1. This paper describes the implementation of an expanded bed adsorption chromatography step into a sequential cultivation process of the yeast in order to link protein expression, cell release, and product capture of the secreted protein in a fully automated plant. The process is operated with a semi-continuous strategy for an integrated production. Process improvements have been achieved using design of experiments. Resulting purities of product achieved up to 87% with recoveries of 51% in a single downstream operation. Furthermore, a multivariate analysis of historical batch data was used to develop a golden batch model for process monitoring.