Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

射孔完井出砂预测新模型及其在射孔优化中的应用

分析了射孔完井的油层出砂机理，以线弹性理论为基础，考虑变温应力和流体渗流作用的拖曳力影响，建立了一种新的射孔完井出砂预测模型。应用该模型研究射孔方位、射孔参数对油井出砂的影响，结果表明，深穿透射孔弹比大孔半径射孔弹能更好地避免孔道出砂，采用定向射孔能有效地减少油井出砂问题。其结果对砂岩油藏射孔优化设计具有一定指导意义。     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。     

沉管隧道水下最终接头施工技术初探

简述了沉管隧道水下最终接头施工技术的应用现状，结合具体隧道工程实例，从外模工程、混凝土结构两方面介绍了最终接头施工技术，表明了该技术具有运用价值。     

数字电路中电源电压瞬间下降的成因及改进

通过分析数字集成芯片多输出中电源电压瞬间下降的原因,对常规驱动电路结构进行改进。改进后单输出电路的峰值电流降为原来的2/3,再通过优化版图的电源布线,能有效防止电源电压下降,使芯片正常稳定地工作。     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

规整填料和新型塔板设计参数选取的质疑及分析

笔者指出了目前规整填料和新型塔板设计计算中若干尚未完全解决的、有争议或值得进一步完善的设计参数。如:规整填料的每米理论板数、最小液体喷淋密度、最小气体空塔动能因子、新型塔板开孔率等,并提出了具体的设计方案供与同行切磋。