磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Prediction of rock mass P wave velocity using blasthole drilling information

In this paper, the development of the models for the prediction of rock mass P wave velocity is presented. For model development, the database of 53 cases including widely used and recorded drilling parameters and P wave velocity was constructed from the field studies conducted in 13 open pit lignite mines. Both conventional linear, non-linear multiple regression and Adaptive Neuro Fuzzy Inference System (ANFIS) were used for model development. Prediction performance indicators showed that ANFIS model presented the best performance and it can successfully be used for the preliminary prediction of P wave velocities of rock masses.     

浅析HPT250轧机中滑移系数对轧制过程的影响

通过HPT250轧机在技术改造中遇到的一个问题，即滑移系数对冷轧元缝钢管在轧制过程中所起的作用。在实际生产中经过不断的技术研究和改进。使闲置多年的HPT250轧机为钢管公司的生产迭拉起到很大的作用。     

几种酚类抗氧剂在润滑油中的应用

采用旋转氧弹法、高压差示扫描量热法等方法研究了5种酚类抗氧剂对6种润滑油基础油氧化安定性的改善效果。结果表明:向加氢基础油中加入0.25%(质量分数)抗氧剂2246-S和RHY510(含硫酚类抗氧剂),可使HVIWH125,HVIWH150,HVIWH500,KN4006,KN40105种润滑油基础油的诱导期由27～88min提高到226～397min;使HVIWH125,HVIWH150,HVIWH300,HVIWH500,KN4006,KN40106种润滑油基础油的起始氧化温度由193.34～198.90℃提高到205.48～230.27℃。     

铝薄膜CMP影响因素分析

提出了在碱性抛光液中铝薄膜化学机械抛光的机理模型,对抛光液的pH值、磨料、氧化剂浓度对过程参数的影响做了一些试验分析。试验结果表面粗糙度的铝薄膜所需的最优化CMP过程参数:硅溶胶粒径为15～20nm,pH值为10.8～11.2,氧化剂浓度为2.5%～3%。     

Characterization and optimization of copper chemical mechanical planarization

The feature scale planarization of the copper chemical mechanical planarization (CMP) process has been characterized for two copper processes using Hitachi 430-TU/Hitachi T605 and Cabot 5001/Arch Cu10K consumables. The first process is an example of an abrasive-free polish with a high-selectivity barrier slurry, while the second is an example of a conventional abrasive slurry with a low-selectivity barrier slurry. Copper fill planarization has been characterized for structures with conformal deposition as well as with bumps resulting from bottom-up fill. Dishing and erosion were characterized for several structures after clearing. The abrasive-free polish resulted in low sensitivity to overpolish and low saturation levels for dishing and erosion. Consequently, this demonstrated superior performance when compared to the International Technology Roadmap for Semiconductors (ITRS) 2000 roadmap targets for planarization. While the conventional slurry could achieve the 0.13-μm technology node requirements, the abrasive-free polish met the planarization requirements beyond the 0.10-μm technology node.     

激光抛光技术的发展与展望

介绍激光抛光技术的发展历史,阐明激光抛光的应用现状及未来的发展前景,论述了激光抛光的工艺特点和作用机理,将激光抛光技术与其它抛光技术进行了全面的对比,指出激光抛光的优势及其存在的问题。     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％     

旋转导向钻井偏心稳定器横向振动研究

旋转导向钻井偏心稳定器横向振动研究是国家863“可控(闭环)三维轨迹钻井技术”课题研究的部分内容。选取偏心稳定器的心轴作为研究对象,以偏心稳定器心轴连续梁系统的横向振动模型受力分析为基础,根据课题研究中所设计的心轴结构形式,建立了与实际情况较为接近的三铰支点的连续梁系统横向振动方程;并分析了偏心稳定器横向振动对钻井工具和钻具系统的影响,为合理进行心轴设计以及偏心稳定器样机在现场的正确使用和钻井参数的合理选择,提供了科学的理论依据和实用的计算方法。计算实例表明,当钻压范围选择在80~250kN时,215.9mm井眼钻进中的确存在19~20、61~63、162~163r/min前三阶横向共振转速区间,因此在选择钻井参数时应通过钻压与转速的配合,尽可能避开横向共振转速,以保证下部钻具组合系统及作业安全。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.