大规格圆钢质量分析和控制

针对湘钢棒材厂生产大规格圆钢出现的表面质量问题，重点介绍了在成品轧机后采用U形辊道和立活套替换棍道；冷床输入辊道采用镶WT合金套；增设高压水除鳞装置；中间轧件尺寸精度控制等措施，成功的解决了大规格圆钢表面擦伤、“麻面”、尺寸超差等表面质量问题，产品质量显著提高。     

K-230B镗床万向护板的设计

介绍了大型机床地坑移动盖板的一般设计思想,根据机床原有功能和结构特点,设计兼顾防尘防屑和美观大方两大特点的活动盖板,为同类设计提供一些参考。     

划痕法测Ni—P合金镀层结合力的研究

本文用划痕法测定了Ni-P合金镀层的结合力;观察了划痕侧面镀层的失效形式;分析了三种评定结合力的参数。结果指出,临界载荷L_C、平均应力σ_A用于评定Ni-P镀层的结合力是有条件的,而B-W公式存在的问题更多。     

金属薄膜结合性能的评价方法研究

针对Al2O3基体上磁控溅射沉积的Au／NiCr／Ta多层金属薄膜，用压痕法、滚动接触疲劳法、摩擦力和声发射两种模式同时监测的划痕法，对比研究了金属薄膜与基体的结合性能。结果表明：压痕试验从压痕形貌上很难判断薄膜与基体是否发生剥离，压入过程中也没有诱发裂纹的产生，更无法分辨薄膜层间的分离；由于金属薄膜的塑性变形，滚动接触疲劳法很难应用于金属薄膜结合性能的表征：划痕法可应用于多层金属薄膜的特异划擦行为研究，其中摩擦力模式能反映压头进入不同金属膜层时的变化，层间声发射信号的灵敏度不如摩擦力信号，对应试验条件，摩擦力曲线存在若干以拐点为特征的载荷，摩擦力曲线上出现的拐点及拐点特征载荷值可以在一定程度上反映多层膜的层数和层厚，并可刻划出该膜／基体系承受压入载荷而不发生剥落的能力。     

Varnish layer hardness of oriental beech (fagus orientalist L.) wood as affected by impregnation and bleaching

The impacts of impregnation and bleaching on the varnish layer hardness of Oriental beech (Fagus orientalist L.) wood were investigated. A number of bleaching combinations {[NaOH−H₂O₂], [NaOH−Ca(OH)₂−H₂O₂], [NaOH−MgSO₄−H₂O₂] [NaHSO₃−H₂C₂O₄], [NaSiO₃−H₂O₂], [KMnO₄+NaHSO₃+H₂O₃]} were applied at 18% concentration for bleaching to both impregnated and unimpregnated specimens of Oriental beech wood. Subsequently, water-based (WB) varnish was coated over the samples and the varnish layer hardness values were determined in accordance with ASTM D 4366-95. All of the chemicals used for bleaching reduced the surface hardness. However, after varnish coating, the hardness of most samples was similar to that of the varnish-coated natural (control) samples.     

纳米助剂新进展

简述了纳米助剂的定义和制备，纳米氧化铝和纳米氧化硅助剂能显著提高涂膜的耐刮擦性而不影响光泽和透明性，纳米氧化锌助剂具有长效紫外线吸收性。     

基于RecurDyn的旋转弹发射出筒过程动力学仿真

针对某旋转弹筒弹分离试验时出现尾翼座与筒壁刮擦的问题,用Recur Dyn对弹体出筒过程进行动力学仿真.对筒弹分离试验进行故障复现,分析故障原因;根据故障分析结论对筒弹设计方案提出更改建议并再次仿真;第二次试验结果表明该分析结论和仿真结果正确.此外,还给出设计方案更改后正常发动机推力状况下的弹体出筒过程的重要总体仿真结果.该研究缩短产品设计周期、降低研制成本.     

Self-emulsifiable soybean oil phosphate ester polyols for low-VOC corrosion resistant coatings

A series of soybean oil phosphate ester polyols (SOPEP) was prepared by reaction of fully epoxidized soybean oil with phosphoric acid and simultanoeous hydrolysis in the presence of a polar solvent. The polyols were characterized by determination of acid value, oxirane number, hydroxyl value, molecular weight (GPC), and FTIR spectra. These polyols with varying amounts of acid phosphate groups could be self-emulsified to form aqueous dispersions after neutralization with organic base. These aqueous dispersion showed varying degrees of stability and their appearance ranged from opaque dispersions to translucent to clear solutions. Waterborne coating compositions were prepared using these aqueous dispersions as principal components and their thermally cured film properties were studied. it was found that by careful selection and formulation, SOPEPs can be successfully used for low-VOC waterborne coating formulations. SOPEPs with 3.5% phosphate ester content showed visibly superior corrosion resistance properties.     

丙烯酸酯聚氨酯/SiO2纳米复合涂层结构与形态对其耐刮伤性影响研究

以四乙氧基硅烷(TEOS)作为主要前驱体,通过改变溶胶-凝胶工艺参数制得了结构和形态各异的丙烯酸酯聚氨酯/SiO2纳米复合涂层,利用TEM、SAXS等手段表征涂层的结构与形态,由洗刷前后涂层的失光率来表征耐刮伤性,详细探讨了纳米复合涂层耐刮伤性与SiO2相特征、有机无机相作用力及SiO2质量分数之间的关系。研究表明:丙烯酸酯聚氨酯涂层中引入纳米SiO2相后,耐刮伤性明显提高。有机相与SiO2相之间的作用力是影响涂层耐刮伤性的最重要因素,作用力越强,耐刮伤性越好。网络状纳米SiO2与颗粒状纳米SiO2相比,更有利于耐刮伤性的提高,且网络状纳米SiO2质量分数越大,耐刮伤性越佳,但SiO2相的致密度和尺寸对耐刮伤性影响较小。对于颗粒状胶体SiO2,在15~160 nm范围内,粒径对耐刮伤性没有明显影响;随着胶体SiO2粒子的质量分数增加,耐刮伤性先增大后减小。     

Effect of surface coating on the screw loosening of dental abutment screws

Regardless of the type of performed restoration, in most cases, a screw connection is employed between the abutment and implant. For this reason, implant screw loosening has remained a problem in restorative practices. The purpose of this study was to compare the surface of coated/plated screws with titanium and gold alloy screws and to evaluate the physical properties of coated/plated material after scratch tests via FE-SEM (field emission scanning electron microscopy) investigation. GoldTite, titanium screws provided by 3i (Implant Innovation, USA) and TorqTite, titanium screws by Steri-Oss (Nobel Biocare, USA) and gold screws and titanium screws by AVANA (Osstem Implant, Korea) were selected for this study. The surface, crest, and root of the abutment screws were observed by FE-SEM. A micro-diamond needle was also prepared for the scratch test. Each abutment screw was fixed, and a scratch on the surface of the head region was made at constant load and thereafter the fine trace was observed with FE-SEM. The surface of GoldTite was smoother than that of other screws and it also had abundant ductility and malleability compared with titanium and gold screws. The scratch tests also revealed that teflon particles were exfoliated easily in the screw coated with teflon. The titanium screw had rough surface and low ductility. The clinical use of gold-plated screws is recommended as a means of preventing screw loosening.