Enhanced transduction coefficient in piezoelectric PZT ceramics by mixing powders calcined at different temperatures

Large transduction coefficient ($d_{33}\times g_{33}$) is difficult to obtain in piezoelectric ceramics because these two parameters show opposite trends with compositional modifications. Herein, the Pb(Zr_0.53Ti_0.47)O₃ ceramic powders were calcinated under different temperatures (A:830 °C, B:860 °C, and C:890 °C), and then mixed together according to different weight ratios (1A:1B:1C, 1A:2B:1C, 1A:2B:3C and 3A:2B:1C) for ceramics preparation. Both d₃₃ and g₃₃ are improved successfully, and the transduction coefficient with the weight ratio of 1A:2B:3C reaches up to 17,500 × 10⁻¹⁵ m²/N, which is 60 % higher than that with the powders calcinated under 830 °C, and at least twice those of commercial PZT-4, PZT-5A and PZT-8 ceramics. The improved transduction coefficient is owing to the enhanced piezoelectric constant and spontaneous polarization resulted from the increased grain size, relative density and the fraction of tetragonal phase. These results indicate that this is a simple but effective way to tailor the transduction coefficient in piezoelectric ceramics.     

MIMO系统的约束广义预测控制

讨论了输出终端带不等式约束情形的多输入多输出系统，说明了这些约束可以通过修改输入柔化系数而使其得以满足，在柔化系数的选择范围确定过程中，为了避免矩阵求逆，采用利用已知数据辨识参数的方法来确定柔化系数，从而使得问题简化。降低了计算量且加快了收敛速度。     

非稳定井流模型的半解析解

为了提高非稳定渗流计算的计算精度 ,通过数学分析得到了水位传导系数随时间变化时 ,一类非稳定渗流井流模型的半解析解 ,并进行了计算比较     

WAVE INTERACTION WITH PERFORATED CAISSON BREAKWATERS

The reflection coefficient of perforated caissons and the total horizontal forces acting on them were experimentally and numerically analyzed and discussed when wave propagates normally. To consider the viscosity effect of fluid and nonlinear action of waves on structures, the VOF (Volume Of Fluid) method combined with the k-ε turbulence model was used to simulate the interaction between waves and structures. Governing equations were solved with the finite difference method. Through 2D experimental study in the wave flume, the empirical relationship between the reflection coefficient of perforated caissons and the main affecting factors were obtained from the experimental data using the least square method. Also the correlation between the ratio of the total horizontal force acting on perforated caisson and the force acting on solid caisson and the main affecting factors were regressed from the experimental data.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

铝冷轧制油应用和生产工艺研究

通过对铝材冷轧工艺的分析。研究，以退火工艺中的斑痕为重点，提出采用加氢处理，异构化精制的石蜡基航空煤油组分为基础油，采用不同复合添加剂生产的通用铝冷轧制油完全可以满足客户要求。     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

Adhesive element modelling and weighted static shape control of composite plates with piezoelectric actuator patches

A novel finite element model is presented for static and dynamic analysis of composite plates integrated with a laminated piezoelectric layer, a host laminated composite plate and an adhesive layer between them. A new adhesive element is developed which includes both peel and shear effects in the adhesive layer based on first‐order shear deformation plate theory. The thin adhesive layer between the piezoelectric layer and the host plate is modelled by assuming that it carries constant shear and peel strains throughout its thickness. In addition, a weighted static shape control scheme for finding the optimal voltage distribution for static shape control is given. By selecting different weighting matrices, a variety of items such as displacements, slopes, curvatures, strains and even generalized forces, can be included in finding the optimal actuating voltage for static shape control. The present model is validated by comparing with those results available in the literature. The numerical results show that the weighted linear least method can give a satisfactory voltage distribution to best match the desired shape. Copyright © 2004 John Wiley & Sons, Ltd.