Analysis and simulations of vibrations of a beam with a slider

A model for vibrations of a beam with a slider is derived, analysed and numerically simulated. It describes a viscoelastic beam that is clamped at one end to a vibrating device, while the other end moves between two stops attached to a slider. The contact is described by the normal compliance or by the Signorini conditions. The existence of weak solutions is established using the theory of set-valued pseudomonotone operators. The model is discretized using fourth-order spatial discretization, the solutions are numerically simulated and their results presented. The dynamics of the vibrations are depicted and so are the noise characteristics of the system.     

Numerical simulation of slider dynamics during slider–disk contact

In this paper, the dynamic behavior of pico slider in contact with the disk was calculated. The analysis model consists of a simplified suspension model, an air bearing model, and a slider–disk contact model. The contact model consists of two elements. One is surface roughness model measured by Atomic Force Microscope (AFM) and the other is micro-waviness model. The dynamic behaviors of the tri-pad slider are calculated at several rotation speeds to investigate slider vibration modes during slider–disk contact. The slider oscillation frequency depends on the rotation speed and it saturates about twice as much as eigen frequency of air bearing pitch mode.     

磁头气膜浮动块浮动特性的影响因素

近年来，随着创新性技术的不断应用，硬盘驱动器的气膜浮动块（以下简称浮动块）也有了较大改进，例如浮动块表面的设计越来越精巧，而性能却更加稳定。因此很好的理解哪些因素是影响气膜浮动块浮动特性的主要原因显得尤为重要。分析这些因素对浮动块的影响结果，有利于我们改进浮动块的特性并对其发展前景做出预测，本文对这些影响因素做了概括总结。     

对震后沙牌拱坝坝肩动力稳定性的再分析

沙牌RCC拱坝是少数经受了大地震考验的百米级高坝实例之一,对其坝肩动力稳定性的再研究意义重大。本文综合有限元法与刚体极限平衡法的优势,提出极限累积位移公式作为滑块失稳判据,开展了两种地震波作用下的沙牌坝肩动力稳定分析并对5.12地震反演的人工波开展了拱坝坝肩稳定性超载分析。结果表明,在反映5.12地震的人工波（ah=2.05 m/s2）作用下,沙牌左右坝肩稳定,与实际地震效应一致。在设计波（ah=5.31m/s2）作用下,沙牌左岸坝肩将失稳,而右岸仍稳定。进行人工波超载分析时,左岸坝肩滑块L1、L2分别经受3.2、3.6倍人工超载波时会发生滑移失稳;右岸坝肩滑块则在4.2倍超载波作用下滑移失稳。此次沙牌坝肩动力稳定再分析考虑了滑块滑移方向及安全系数瞬态变化对滑块累积位移的影响,更真实地反映了沙牌拱坝坝肩滑块滑移规律,为工程实际中的坝肩动力稳定分析提供了一个新思路。     

曲柄滑块机构惯性力部分平衡的平衡重选取的优化方法

采用线性独立向量法推导了曲柄滑块机构剩余惯性力的普遍表达式。并以机构最大剩余惯性力最小为优化准则。对曲柄滑块机构惯性力部分平衡最佳平衡量的选取进行了理论分析，给出了求取最佳平衡量的计算机数值计算算法框图。     

Control Model for Large‐Sized Gantry Type Linear Motor Slider

At present, many industrial carrier devices utilize linear motor sliders. However, a heavier load requires a linear motor (which is an example of a direct drive device) to get higher power, compared with a rotary motor with a ball screw slider (which is an example of an indirect drive device). In order to obtain higher power at a lower cost, a linear slider with multiple motors can be utilized, for example, a gantry type linear motor slider. Moving the gantry type slider requires two linear motors that are set up in parallel to enable synchronization control. Some conventional synchronization control methods have been proposed for the parallel twin linear slider; however, a large‐scaled gantry type linear motor slider has two unique problems: mechanical distortion caused by the limitations of installation environment and coupling caused by joints with low stiffness. This paper proposes a control model to solve these problems, and an identification method of each parameter. Furthermore, the effectiveness of the control model is verified by comparison with simulation results and experimental results.     

弧形滑块抽芯机构注射模设计

通过分析对比BDCI塑件中手柄主体的结构特征,设计出弧形滑块抽芯机构中抽芯的典型结构,实现模具结构合理,动作可靠,塑件顺利成型。     

串珠机物流套注射模设计

设计了带双层哈夫滑块脱模机构的三板模实现串珠机物流套的注射成型,针对塑件外壁脱模困难,使用2层哈夫滑块机构对塑件的外壁实施侧抽芯脱模,两层哈夫滑块的驱动分别由三板模的2次分型驱动。实践证明,模具结构和脱模机构布置合理,具有一定的参考作用。     

45°斜抽芯滑块注射模设计

以注射模中斜抽芯机构为研究对象,对于较大的斜抽芯角度,通过对滑块结构进行优化、导向T形槽和复合角度受力驱动转换,简化抽芯机构结构,使受力驱动合理,并介绍了模具的工作过程。这种滑块结构使模具设计更合理,结构更紧凑,动作稳定可靠,提高了成型塑件的质量和生产效率。     

助力筒带2种多次抽芯机构热流道注射模设计

针对筒形塑件的模具设计困难问题,设计了一种简化型1模1腔两板注射模具来实现其自动化注塑成型.模具中,采用卧式布局来简化模腔的分型,简化了模具整体结构.使用了热流道浇注系统来保证模腔的成型质量.塑件内、外壁的脱模使用了3种4个机构来进行抽芯脱模,一种为油缸滑块单次抽芯机构,一种为油缸+斜导柱3次抽芯机构,一种为哈夫滑块双...