Revisit the Pitot static tubes in the standards

A Pitot tube is a popular device used for the measurements of flow fields. To control the accuracy of the Pitot tube coefficient, the international standard organization (ISO), the American Society for Testing and Materials (ASTM), and the Japanese Industrial Standards (JIS) issued guidelines that recommended the shape and working conditions of these devices. However, many Pitot tubes on the market do not follow these guidelines. In the present study, various types of Pitot tubes in the market were tested at the National Metrology Institute of Japan (NMIJ) to determine the effects of the geometry and flow characteristics. The results revealed certain limitations in the existing ISO and JIS standards, specifically with regard to the recommended design parameters of the AMCA Pitot tube, the reference coefficient value for the JIS Pitot tube, and the redefinition and limitation of Reynolds numbers pertaining to Pitot tube working conditions.     

Calcium deficient hydroxyapatite by precipitation: Continuous process by vortex reactor and semi-batch synthesis

Precipitation of calcium deficient hydroxyapatite nanoparticles in an environmentally benign manner by using only dilute solutions of calcium hydroxide and phosphoric acid without pH adjustment and addition of other chemicals, and water, being the only by-product was investigated by using continuous flow Vortex Reactor (VR) and Semi-Batch Reactor (SBR). The effect of hydrodynamics by changing the Reynolds number of the jets providing residence times of 8.4 ms to 4.37 s for VR, and by changing the stirrer speed between 100 rpm (Re = 2656) and 1000 rpm (Re = 26560) for SBR, on the particle size, particle size distribution, and morphology of the particles was investigated for both systems. It has been shown that it is possible to produce pure phase hydroxyapatite nanoparticles in the desired morphology by changing production system, without resorting to additives. While VR produced rod-like particles with the crystallite size around 4 nm, SBR produced spherical particles with the crystallite size of around 5 nm.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

A facile co-solvent strategy for preparation of graphene nanoplatelet powder: An industrially viable innovative approach

We report an industrially viable promising approach to produce micrometer-sized multilayer graphene nanoplatelet powder (MGNP) in a scalable quantity via microwave-assisted exfoliation of graphite (MEG) and fragmented into MGNP through liquid-phase exfoliation in the co-solvent mixture by kitchen mixer (KM). KM allows rapid delaminating MEG into MGNP by shear force dominated exfoliation. Majority of MGNPs are with a diameter of few micrometers and thickness is in nanometers. MGNP are crystalline with very limited defects was confirmed by Raman measurements and transmission electron microscopy. This process transforms, more than 86% of graphite flakes into MGNP. This advanced approach opens a new pathway to produce MGNP in bulk quantity as it is feasible, rapid, and cost-effective.     

Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

Animations showing Lego manipulative tasks: Three potential moderators of effectiveness

Evidence suggests that transient visual information, such as animations, may be more challenging to learn than static visualizations. However, when a procedural-manipulative task is involved, our evolved embodied cognition seems to reverse this transitory challenge. Hence, for object manipulative tasks, instructional animations may be more suitable than statics. We investigated this argument further by comparing animations with statics using a Lego task shown to university students, by examining three potential moderators of effectiveness: (a) the environment of manipulation (virtual or physical), (b) the quality of visual information (focused or unfocused), and (c) the presence of hands (no hands or with hands). In Experiment 1 we found an advantage of animation over statics, and no differences among the environments. In Experiment 2, we again observed an animation advantage, a small advantage of focused static information compared to unfocused static information, and a positive effect of not showing the hands.     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

基于对比折射法的三维静校正技术及其应用

在地形起伏剧烈、速度和厚度横向变化大的地区，折射静校正技术的应用受到诸多限制，主要表现在不能准确地识别和拾取来自于地下连续地质界面的折射波，使得精确求取的长波长静校正量困难。为此，提出了一种基于对比折射法的三维静校正技术。介绍了这种静校正技术的方法原理和特点，基于对比折射法的折射波至拾取实质上是一个折射层的对比分析解释过程，因此能准确地拾取折射波至，精确地求解低速带的绝对延迟时；然后利用延迟时和近地表速度模型（等效，时深，空变）反演表层模型，最终一次性完成基准面静校正（包含低速带校正和高程校正）。在黄土塬、沙漠以及沙漠和山地的接合部等地区，利用基于对比折射法的三维静校正技术进行静校正处理，使资料的品质得到了明显改善，反射同相轴连续性好，信噪比和分辨率高，构造形态清晰可靠，提高了勘探精度。     

大型弧形闸门静力特性有限元分析

以某水电站溢洪道弧形闸门为例,建立了大型弧形闸门的有限元分析模型,应用ANSYS软件对其在各种工况下的支铰反力、闸门应力、位移挠度以及屈曲失稳等静力特性进行了计算分析,为完善闸门结构的设计提供了依据,对同类闸门结构的设计计算有参考意义。