Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

埋地管道在冻土带的热力变形分析

埋地油气管道通过永冻土地带时,由于管内介质与周围的冻土发生了热力作用,使冰土解冻,在管道周围形成融化圈。文章分析了永冻土的特点,建立了永冻土地带土壤传热数学模型:融化圈内外传热方程、管道向土壤和土壤表面向大气所放热量的守恒关系、融化圈界面处土壤温度、相变界面处固相变为液相的传热条件。还建立了埋地管道模型,并以穿过永冻土地带土壤的输油管道为例,分析并计算了各种应力的最大值所在的位置和大小,提出了在永冻土地带减小管道热力变形的措施。     

ca油田稠油油藏系统保护油气层研究

针对ca油田多层状砂泥薄互层稠油油藏的特点,开展了热采和非热采条件下储层变化特征研究、钻井和固井过程入井液的研究、采油工艺技术等系统保护油气层研究,了解各种变化的作用过程和原因,有效地预防现场施工中可能发生的储层伤害,从而达到储层保护、提高采收率的目的。     

从稳态到动态的空气调节

分析传统空调所提供的稳态参数微气候环境不一定能达到人的舒适和健康的要求,提出符合人本身生理习惯的空调送风方式应该是动态空气调节.认为个人可调节和适宜的环境渐变能同时保证舒适和健康两方面需要.     

Phosphorus‐containing polyaryloxydiphenylsilanes with high flame retardance arising from a phosphorus–silicon synergistic effect

Polyaryloxydiphenylsilanes were prepared from phosphorus‐containing diols and diphenydichlorolsilane through solution polymerization. With a stoichiometric imbalance in feed monomers, the resulting polymers exhibited moderate melting points and good processing properties. The polymers prepared showed initial decomposition temperatures above 340 °C, excellent thermal stability, high char yields at 850 °C and very high limited oxygen index values of 56–59. The polymers' char yields and their (P + Si) contents showed linear relationships. © 2003 Society of Chemical Industry     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.