45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

基于MSP430F11X的低功耗温度记录仪

本文详细介绍了基于MSP430F11X的大容量低功耗温度记录仪的工作原理及软硬件设计方法,并给出了实际应用的硬件电路和程序源代码。     

国产掘进机在龙门滩引水隧洞施工中的应用

在长隧洞的施工中，采用掘进机施工的工程越来越多，特别是国外掘进机的引进，加快了长隧洞工程的开发。而国产掘进机由于其性能和材质方面的原因，存在着一定的技术缺陷．通过国产SJ-45型掘进机在龙门滩工程的施工应用，分析和总结了SJ-45型掘进机的机械性能和存在的技术问题及处理结果，以利于国产掘进机的科研、生产和施工。     

Ti-45Al-10Nb合金的高温氧化行为

研究了Ti—45A1—10Nb(原子分数，％)合金在800-960℃在氧气和空气中的氧化行为．结果表明，该合金具有较好的高温抗氧化性能，其氧化增重速率与铁基耐热不锈钢相似或略优．与Ti—50A1合金相反，Ti-45A1-10Nb合金在空气中的氧化增重速率明显低于在纯氧中的氧化增重速率．X射线衍射与能谱分析表明，Ti-45Al一10Nb合金在氧气中的氧化产物主要有TiO2和Al2O3，但在空气中的氧化产物中有TiN相．这是降低氧化速率的主要原因，同时，合金元素Nb稳定了氧化层中的TiN相，因而提高了合金在空气中的抗氧化性能．     

锦45块“八五”期间新增可采储量技术途径研究

方法 利用注采特征曲线，对锦４５块“八五”期间新增可采储量进行了计算研究，目的 研究蒸汽吞吐阶段增加可采储量的途径，为同类油藏的合理开发提供依据，结果 蒸汽吞吐阶段增加可采储量的三项技术途径；一是加大滚动勘探开发力度，不断发现和投入新储量；二是开展油藏工程研究，搞清油水分布，合理部署调整井，三是综合治理，增加可采储量。结论 “八五”期间，利用上述技术途径，改善了锦４５块开发效果，新增可采储量２７１     

表面电沉积合金层提高碳钢齿轮的接触疲劳强度研究

 接触疲劳破坏是齿轮的主要失效形式之一． 在45#钢齿轮齿面电沉积Ni-P-Co合金层，可以显著提高其接触疲劳强度．同时，对合金层的表面形貌，表面粗糙度、显微硬度和疲劳点蚀坑形貌特征等进行了分析．     

LD-LF-CC生产45^#质量研究与实践

莱钢采用LD-LF-CC（方坯连铸）生产45^#钢铸坯质量存在较多问题,主要是表面气孔数量多、轧材顶锻裂纹等。从对顶锻裂纹缺陷进行金相分析、扫描电镜分析出发,研究45^#钢铸坯表面气孔形成的原因;生产实践中,通过采取控制钢中气体含量的措施,使45^#钢铸坯质量得到全面改善。     

CCUS in a net-zero U.S. power sector: Policy design,rates, and project finance

Carbon capture utilization and storage is an important technology option to rapidly and profoundly decarbonize the power sector, but will not deploy without substantial incentives or regulation. Assessment of U.S. policy options reveals that current incentives only partially close the finance gap and are most sensitive to fuel type and ownership structure. Recent proposed legislation would in some designs attract private investment for many projects, leading to widespread deployment of CCUS in the power sector. Additional constraints and concerns (including technology options and presence of CO₂ infrastructure) could play an important secondary role. This study discusses the specific US incentive policies that can provide investors and lenders with net cash flows that are adequate to attract private capital to CCUS power projects in the US.     

Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.