乘累加运算器的高性能解决方案

在设计数字信号处理器时我们经常要设计高性能的乘累加运算器，文章详细分析了乘累加运算器的结构，提出了其高性能设计方案并采用标准单元进行了实现，同时提出了DCT运算单元的高性能解决方案。     

The effect of doubly tapered strut morphology on the plastic yield surface of cellular materials

Although the literature on the mechanics of cellular materials is vast, there is no theoretical model to account for the effects of axial yielding of struts aligned to the applied loading direction on the plastic yield surface under multiaxial loading conditions. An anisotropic hexagonal model having tapered strut morphology is developed to show these effects on the plastic yield surface under multiaxial tensile loading condition. This model covers several types of cellular structure such as two-dimensional (2D) hexagonal and square cellular materials, and three-dimensional (3D) hexagonal and rhombic cellular materials of rod-like columnar structure. A tetrahedral element with tapered strut morphology is also used for a foam model to illustrate these effects on the yield surface under axisymmetric loading condition. Plastic collapse due to bending moment in the inclined struts is a dominant mode. However, under multiaxial tensile loading, the collapse due to axial yielding of struts parallel to the loading direction is found to be an important mode. The shape of plastic yield surface was found to depend not only on relative density but also on the strut morphology.     

Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

引进型国产300MW汽轮机窜轴事故分析及防止对策

通过引进型国产300MW汽轮机在启动试运中出现的一次窜轴事故,根据计算机追忆打印的有关图表、数据分析了产生事故的原因,并提出了为防止类似事故重演应采取的措施和建议。经采取措施后该机组多次又在相同情况下启机,已安全运行。说明分析正确,措施得当,值得同类型机组借鉴。     

Molecular orientation and stress in biaxially deformed polymers. II. Steady potential flow

The development of biaxial segmental orientation and stress in a flexible-chain polymer fluid subjected to steady biaxial extensional flow is analyzed. Closed-formula model based on the Padè approximation of the inverse Langevin function in the non-Gaussian distribution of the chain end-to-end vectors is considered. The approach is free from the limitations related to finite chain extensibility and slow convergence of the series expansion formulations at higher chain deformations.Segmental orientation is characterized by the average orientation tensor, related axial orientation factors and global orientation anisotropy. Orientational behavior and corresponding stresses in the biaxial elongational potential flow are discussed in a wide range of elongation rates. Orientation characteristics calculated for the biaxial flow deformation are much higher than those predicted for the affine biaxial stretch deformation in polymer solids.     

重油催化裂化装置轴流风机的损坏与修复

广州分公司炼油厂重油催化裂化装置四机组轴流风机在 1998年 9月由于入口消音器故障引发重大事故 ,严重影响了装置生产。该文主要针对其损坏的原因、情况和修复方法作了探讨和论述     

降低冰箱噪声的试验研究

本文对一种冰箱匹配高效活塞式压缩机后噪声较大的问题进行了研究。这种噪声的峰值频率介于2 0 0～ 315Hz (1/ 3倍频程 )。本文确定了吸气管振动所形成的冰箱蒸发器的振动是产生噪声的根源 ,而吸气管的振动源为机壳的振动和气流脉动 ,并且气流脉动是主要激振力。在上述分析与试验的基础上 ,重新设计压缩机的吸气消音器 ,在吸气管壁钻孔 ,通过这些措施 ,使该冰箱的声功率降低了约 2dB (A) ,提高了冰箱的声质量     

天然气管道燃压机组的性能试验及见证

结合西气东输管道工程燃气轮机驱动压缩机组设备订货及验收中对性能试验项目的确定、工厂试验及见证过程,介绍了燃压机组性能试验项目所涉及的主要内容、执行标准、需要达到的技术指标,各种性能试验的基本情况,买方参加工厂试验见证中需要重点处理好的问题等。以期为我国其他大型长输天然气管道机组订货及试验见证工作提供借鉴。     

用于数控设备的弹性环联轴器

介绍了一种适用于数控设备改造的无键联轴器，从其原理、设计、加工各方面作了阐述，并且总结了许 多实际应用经验和适用参数。     

轴向柱塞泵配流副油膜的实验研究

本文介绍了对６３ＣＹ１４－ＩＢ型轴向柱塞泵配流副油膜的实验研究结果。该研究结果为改进该泵配流副的性能提供了依据。