Fracture toughness of thermoset composites reinforced by perfectly bonded impenetrable short fibers

The fracture toughness of brittle thermoset resins could be improved significantly by perfectly bonded tough, short fibers through both crack trapping and bridging effects. In this paper, the crack trapping effect was studied through the analysis of the change of strain energy associated with the crack propagation across a regular array of fibers, and the bridging effect was discussed based on the Andersson–Bergkvist model. The fracture resistance increases with the fiber volume fraction, and is independent of the elastic properties of the matrix, the crack length, and the cross-sectional diameter of the fibers.     

THE FRACTURE MECHANISM OF 475°C EMBRITTLEMENT IN A DUPLEX STAINLESS STEEL

The mechanism of “475°C embrittlement” of a duplex stainless steel was investigated using finite element modelling of the stress distribution at brittle fracture initiation. Brittle fracture initiated at a critical shear stress, which increased with ferrite hardness. The fracture stress was affected by the duplex microstructure. Fracture was nucleated by deformation twins, which were identified using electron back-scatter diffraction. The ductile-to-brittle fracture transition was sensitive to age-hardening and could be described simply by the effect of age-hardening and test temperature on the yield stress.     

油泵柱塞和轴承外套失效分析

对断裂的油泵柱塞、轴承外套从成分、组织、工艺等方面进行了检验分析。结果表明，柱塞首先断裂，断裂后的柱塞碎片卡住了轴承外套，使轴承外套过载脆断。而柱塞的断裂是由于热处理不当，造成淬火加热温度过高，使柱塞的显微组织出现粗大的针状马氏体，并引起淬火裂纹，导致柱塞的韧性下降，脆性增大，随着载荷作用和液压油的渗入，裂纹进一步扩展，当裂纹扩展笃柱塞有效载面积承受不了全部工作应力时，发生脆性断裂。     

双头螺栓失效分析

与汽车电机装配在一起的双头螺栓在拧紧后不久便发生断裂。采用扫描电镜、化学分析、金相检验等方法对失效件进行了检测，同时又进行了氢脆试验验证。结果表明，螺栓在进行表面酸洗及电镀时，氢向金属内部扩散和富集，当氢浓度达到一定临界值后，促使氢致裂纹的产生和扩展。在外应力的作用下，即出现氢脆现象导致螺栓断裂。     

Environmental etch performance, and scratch and mar of automotive clearcoats

Environmental etch damage to automotive coatings, and scratch and mar of these coatings are an important element of customer satisfaction as well as a significant warranty repair consideration for automotive companies. The conditions that result in environmental etch are examined and a laboratory test proposed. Data from this test are compared to automotive hoods exposed in Florida. The performance of various crosslinking chemistries is discussed and the requirements for improved environmental etch are outlined. Scratch and mar performance of these systems is also reviewed. We have found that coatings respond to physical stress by elastic recovery, by plastic flow and by brittle fracture. Classifying types of damage in this way is important for understanding the chemistry needed for improved scratch and mar of coatings.     

组合定位中选星算法的改进研究

在多个系统组合定位模式下,可视星数量大幅增加,为更精准稳定的定位提供了可能.在现有选星算法中,由于未考虑实际作业中的一些问题,如:障碍物对卫星信号传播路径的遮挡等,估算得到的较好卫星选取方式在实际定位中无法正常发挥作用,同时在接收机内部计算中会应用大量的矩阵求逆运算,增加了计算量,占用了较多的系统资源.提出了基于可视星仰角来初筛卫星,通过GDOP结合星座四面体法得到选星组合的方法.讨论了设定卫星仰角时的取舍问题.新算法在理想情况和实际情况下寻找有效定位平衡点,以规避无效选星并减少计算量.     

Some Expressions for the Strain Energy in a Finite Volume Surrounding the Root of Blunt V-notches

The paper gives some closed form expressions for the strain energy averaged in a finite size volume surrounding the root of blunt V-shaped notches under Mode I loading. The control volume, reminiscent of Neuber’s concept of elementary structural volumes, is thought of as dependent on the ultimate tensile strength and the fracture toughness K_IC in the case of brittle or quasi-brittle materials subjected to static loads. Expressions for strain energy density under plane strain conditions and Mode I loading have been derived from an analytical frame recently reported in the literature, which matches Williams and Creager-Paris’ solutions in the particular cases of plates weakened by sharp V-notches or blunt cracks (U-notches), respectively. In order to validate a local-strain-energy based approach, a well-documented set of experimental data recently reported in this journal by Gómez and Elices has been used. Data refer to blunt and sharp V-specimens of PMMA subjected to static tension loads and characterised by a large variability of notch root radius (from 0 to 4.0 mm) and notch angle (from 0° to 150°). Critical loads obtained experimentally have been compared with the theoretical ones, estimated here by keeping constant the mean value of the strain energy in a well-defined small size volume.     

Development of specimen and test method for strength analysis of MEMS micromirror

Specimens and fracture test methods for strength analysis of MEMS micromirrors were proposed. Bending and combined loading tests were performed, and torsion strength was estimated from those results. Two-parameter Weibull distribution was used to evaluate the fracture stresses estimated from the FEM model. The resulting scale and shape parameters were 787 MPa and 7.77 for the bending test and 517 MPa and 5.28 for the combined loading test. There was a difference in strength between the results of the bending and combined loading tests. From the load factor analysis, it was found that both geometry and stress distribution have to be considered to estimate the strength of MEMS since flaws are non-uniformly distributed. It was also found that torsional strength can be estimated on the safe side using the results of the combined loading test.     

Cracked Brazilian disc specimen subjected to mode II deformation

The centrally cracked Brazilian disc specimen has been used by many researchers to study mode I and mode II brittle fracture in different materials. However, the experimental results obtained in the past from this specimen indicate that the fracture toughness ratio (K_IIc/K_Ic) is always significantly higher than the theoretical predictions. It is shown in this paper that the increase in the ratio K_IIc/K_Ic can be predicted if a modified maximum tangential stress (MTS) criterion is used. The modified criterion takes into account the effect of T-stress in addition to the conventional singular stresses. The fracture toughness ratio K_IIc/K_Ic is calculated for two brittle materials using the modified criterion and is compared with the relevant published experimental results obtained from fracture tests on the cracked Brazilian disc specimen. A very good agreement is shown to exist between the theoretical predictions and the experimental results.