Enhancement of thermal,mechanical, ignition and damping response of magnesium using nano-ceria particles

Magnesium (Mg)-based nanocomposites owing to their low density and biocompatibility are being targeted for transportation and biomedical sectors. In order to support a sustainable environment, the prime aim of this study was to develop non-toxic magnesium-based nanocomposites for a wide spectrum of applications. To support this objective, cerium oxide nanoparticles (0.5?vol%, 1?vol%, and 1.5?vol%) reinforced Mg composites are developed in this study using blend-press-sinter powder metallurgy technique. The microstructural studies exhibited limited amounts of porosity in Mg and Mg-CeO₂ samples (< 1%). Increasing presence of CeO₂ nanoparticles (up to 1.5?vol%) led to a progressive increase in microhardness, dimensional stability, damping capacity and ignition resistance of magnesium. The compressive strengths increased with the increasing addition of the nanoparticles with a significant enhancement in the fracture strain (up to ~48%). Superior energy absorption was observed for all the composite samples prior to compressive fracture. Further, enhancement in thermal, mechanical and damping characteristics of pure Mg is correlated with microstructural changes due to the presence of the CeO₂ nanoparticles.     

不同表面预处理对有机电致发光显示器性能的影响

从生产角度研究了基板表面的预处理工艺对OLED性能的影响,分别用UVOzone、氧Plasma以及两者相结合的方式对基板进行表面处理,并按照生产工艺制作器件,从接触角、方阻以及光电特性等测试结果对各种表面处理的样品进行比较。结果表明以上处理都改善了器件性能,不同程度提高了器件的清洁度、亮度和发光效率,其中UVOzone和氧Plasma结合的方式处理效果最为显著,器件在10V时亮度达到79920cd/m2,比其他两种处理方式亮度提高约25%。     

Relating catalyst structure and composition to the water–gas shift activity of Cu–Zn-based mixed-oxide catalysts

In order to investigate the effect of cerium oxide on Cu–Zn-based mixed-oxide catalysts four catalyst samples were characterized by means of XRD, in situ XANES and thermogravimetric analysis. The activity of the catalyst samples was tested for the forward water–gas shift reaction. Cerium oxide was found to increase the crystallinity of the ZnO phase indicating a segregation of the Cu and ZnO phases. The TOF of the water–gas shift reaction based on chemisorption data was found to be independent of composition and preparation conditions of the four catalyst samples. In contrast, the catalyst stability depends on composition and preparation conditions. Cerium oxide impregnated before calcination of the hydrotalcite-based Cu–Zn precursors leads to a more stable water–gas shift catalyst.     

Effects of surfactant/silica and silica/cerium ratios on the characteristics of mesoporous Ce-MCM-41

Using the surfactant CTMABr (cetyltrimethyl ammonium bromide) and cerium(IV) sulfate, mesoporous Ce-MCM-41 molecular sieves were produced under a hydrothermal condition with various surfactant/silica (surfactant/Si) and silica/cerium (Si/Ce) ratios. Changes to the structural traits caused by changing the molar ratios of both surfactant/Si and Si/Ce were investigated. XRD (X-ray diffraction), FT-IR (fourier transform infrared spectroscopy), and SEM (scanning electro microscopy) were used for the characterization of prepared mesoporous samples. Among the tested molar ratios, surfactant/Si ratio of 0.5 and 0.2 showed highest values of d_1 0 0 and intensity, respectively, for the Si-MCM-41. XRD analysis also identified a quintessential hexagonal structure of Ce-MCM-41 for the Si/Ce molar ratio higher than 40 (maintaining the surfactant/Si ratio at 0.2). When cerium content was increased to have the Si/Ce molar ratio of 20, the hexagonal structure of Ce-MCM-41 was collapsed due to the structural stress of substituted cerium. FT-IR results confirmed calcination of Ce-MCM-41 and the incorporation of Ce⁴⁺ ions of cerium sulfate into the silica surface with proper removal of the surfactant. Rod-like shape with rounded edges of the prepared Ce-MCM-41 samples was identified by SEM. These results suggest surfactant/Si ratio of 0.2 and Si/Ce ratio of 40 for the production of Ce-MCM-41 with the highest level of crystallinity.     

Surface Chemistry and Catalysis of Rare Earth Oxides I．A Study of the Reactivity of Surface Hydroxyls on CeO_2 and Pr_6O_（11） by FT－IR Spectroscopy

ＳｕｒｆａｃｅＣｈｅｍｉｓｔｒｙａｎｄＣａｔａｌｙｓｉｓｏｆＲａｒｅＥａｒｔｈＯｘｉｄｅｓＩ．Ａ　ＳｔｕｄｙｏｆｔｈｅＲｅａｃｔｉｖｉｔｙｏｆＳｕｒｆａｃｅＨｙｄｒｏｘｙｌｓｏｎＣｅＯ_２ａｎｄＰｒ_６Ｏ_（１１）ｂｙＦＴ－ＩＲＳｐｅｃｔｒｏｓｃｏｐｙ...     

Studies on the corrosion behavior of cerium-implanted zircaloy-4 with GAXRD

In order to study the influence of cerium ion implantation on the aqueous corrosion behavior of zircaloy-4, specimens were implanted by cerium ions with a fluence range from 1×10¹⁶ to 1×10¹⁷ ions/cm² at maximum 150°C, using MEVVA source at an extracted voltage of 40 kV. The valence and elements penetration distribution of the surface layer were analyzed by X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the cerium ion implantation in the oxide films. Three-sweep potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zircaloy-4 in a 1 N H₂SO₄ solution. It was found that a significant improvement in the aqueous corrosion behavior of zircaloy-4 implanted with cerium ions compared with that of the as-received zircaloy-4. The improvement effect will declined with raising the implantation fluence. The bigger is the fluence, the less is the improvement. Finally, the mechanism of the corrosion behavior of the cerium-implanted zircaloy-4 is discussed.     

活性炭载体的超声波处理对Pt／C催化剂活性的影响分析

通过对活性炭载体进行不同条件的超声波处理获得了具有不同表面化学性质的载体，使用比表面积（BET）、酸碱滴定等技术手段对载体的物理化学性质进行了表征。将经过超声波处理的活性炭载体制备成Pt／C催化剂，并将催化剂直接用于催化反应，考察了活性炭载体的不同超声波处理条件对Pt／C催化剂性能的影响。实验发现，活性炭载体经过超声波处理后，表面灰分含量、pH值和中孔孔容有较大的变化；使用经过60min超声波处理后中孔孔容较大的活性炭作为载体制备的Pt／C催化剂，在催化加氢反应性能测试中显示了最高的催化活性。在此基础上，就活性炭载体的超声波处理对Pt／C催化剂活性的影响进行了讨论。     

有机涂层钢板生产线主要工艺

介绍了有机涂层钢板生产线上钢基板的预处理,全线张力控制,纠偏装置的布置,固化炉的选型.     

Effect of HCl pre-treatment on corrosion resistance of cerium-based conversion coatings on magnesium and magnesium alloys

The corrosion protection afforded by a cerium conversion coating, formed by immersion in a solution containing rare earth salt and hydrogen peroxide, on pure magnesium and two magnesium alloys, AZ91 and AM50, has been studied. The effect of HCl pre-treatments on the morphology and on the corrosion resistance of the cerium conversion layer was investigated. A thicker and more homogeneous distribution of the conversion coating was obtained when the sample surface was pre-treated with acid. Higher amounts of cerium on the surface of the pre-treated samples were detected. The cerium conversion coating increased the corrosion resistance of the alloys because it ennobled the corrosion potential and decreased both the anodic and cathodic current. The acid pre-treatment further increased the corrosion resistance of the coated alloys. After five days of immersion in chloride environment the untreated samples showed localized corrosion while the chemical conversion coated samples appeared unaffected.