Anti-coking and anti-carburizing behavior of amorphous AlPO4 coating

The aim of the present study was to examine the anti-coking and anti-carburizing behavior of amorphous AlPO₄ coating. So, aluminum phosphate composition was synthesized by sol-gel process and applied on the AISI 304 stainless steel by dip coating technique. Anti-coking performance was examined in a tube furnace at 1000 °C for 30 min under Ethane (C₂H₆) atmosphere. Carburizing test was performed in a sealed charcoal medium at 1100 °C for a total of 30 h exposure time. Phase composition of the samples was analyzed by X-Ray Diffraction (XRD) after coking and carburizing tests. Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray Spectroscopy (EDS) were employed to study the morphology and elemental analysis of the samples after coke and carbon formation experiments. Microhardness indenter was applied on the cross section of the carbon-exposed specimens to plot the hardness profile through the carburizing zone. The results of the coking experiment revealed catalytic coke formed on the uncoated surface, while irregular spherical coke with no trace of catalytic coke was formed on the coated surface, indicating the great anti-coking performance of the amorphous AlPO₄ coating. The results of pack-carburizing test demonstrated that the thickness of the carbide layer formed on the bare surface was ～10 times greater than that of the coated sample. Hardness measurement for the amorphous AlPO₄ coated sample detected lower values compared to those for the uncoated one at all distances from the surface, indicating less carbon diffusion occurred beneath the coated surface. In overall, the results declared that the amorphous AlPO₄ coating could be a good candidate for surface protection of stainless steel against catalytic coke formation and carbon diffusion.     

低分子量聚丙烯酸钾的合成及其应用

采用水溶液聚合法制备了低分子量聚丙烯酸钾（PAAK），并作为新型消焰剂加入单基发射药中。通过火焰原子吸收光谱法测试了PAAK中钾的含量；用乌氏黏度计测定了特性黏度；采用DSC法研究不同pH值的PAAK与硝化棉（NC）的相容性；利用充氮氧弹法对添加PAAK、硝酸钾KNO₃、硫酸钾K₂SO₄的单基发射药的燃烧残渣进行了对比研究。结果表明，合成的PAAK中，钾的质量分数为15.21%，相对分子量在3 000左右，有利于和NC均匀混合，且在中性或微碱性（pH＝7.0~7.5）的情况与NC相容性良好。与传统的KNO₃、K₂SO₄消焰剂相比，PAAK能够和NC均匀混合，制备均质透明的单基发射药；PAAK发射药的燃烧残渣最少，占发射药质量的0.18%。     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

Effect of hyperbranched poly(citric polyethylene glycol) with various polyethylene glycol chain lengths on starch plasticization and retrogradation

A series of hyperbranched poly(citric polyethylene glycol) (PCPEG) materials with varied polyethylene glycol (PEG) chain lengths as plasticizers were mixed with maize starch (MS) via cooking and film‐forming. The structure, pasting property, plasticization, aging property, moisture absorption and compatibility of plasticized starches were studied by means of Fourier transform infrared spectroscopy, X‐ray diffraction, rapid viscosity analysis, tension testing, moisture absorption measurements and scanning electron microscopy. Compared with PEG and citric acid, PCPEG was more effective in promoting starch chain movement and inhibiting the retrogradation of starch film. Also, PCPEG/MS had smaller moisture content. The longer the plasticizer chain, the better were the aging resistance and moisture resistance of starch. But with an increase of PEG chain length, mechanical properties of PCPEG/MS deteriorated and the compatibility between PCPEG and MS decreased. The hyperbranched derivative of PEG with longer chain exhibited improved plasticization and compatibility with starch. © 2019 Society of Chemical Industry     

Hydroxyapatite/tricalcium silicate composites cement derived from novel two-step sol-gel process with good biocompatibility and applications as bone cement and potential coating materials

Tricalcium silicate (C₃S) and hydroxyapatite (HAp) composites were fabricated through the sol-gel process. The aim of this research is to improve the biocompatibility of C₃S through HAp addition and study the potential of using this as coating materials. The composites (HAp/C₃S) were characterised by Fourier transform infrared spectrometry, thermal gravity-differential thermal analysis and X-ray diffraction. The working and setting times of cement pastes were tested using Gillmore needle. Mechanical properties were examined by nanoindentation and material testing system. In vitro biocompatibility of the materials were studied by cell attachment and viability of L929 and MG-63 cells. HAp/C₃S as a coating material on gelatin film were measured with the surface roughness and imaged by scanning electron microscope. With the addition of HAp, no undesirable free CaO was detected with the synthesis by the sol-gel preparation. The pH values of HAp added groups were between 7.54 and 8.76, which were much lower than pure C₃S group (pH?=?11.75). For in vitro studies, the presence of HAp could effectively enhance the cell attachment and viability of both L929 and MG-63 cells grown in the extract or directly on the composites. However, the mechanical properties of the composites were impaired as compared to pure C₃S. Lastly, HAp/C₃S cement could be evenly coated on gelatin film. HAp is successfully demonstrated to improve C₃S biocompatibility with this new composites HAp/C₃S. C-75 (75% C₃S and 25% HAp), in particular, has good biocompatibility, relatively high compressive strength and can be uniformly coated onto gelatin film. Thus, C-75 is a promising material for further investigation as a coating on other biopolymers.     

Dye removal by polymer derived ceramic nanobeads

Emulsion processed polymer derived ceramic (PDC) nanobeads are used for Methylene Blue dye removal from aqueous solutions. The PDC nanobeads, produced at 600 °C and 1200 °C pyrolysis, are subsequently coated with titania (anatase). Titania-coated nanobeads show less than 35%, i.e., limited dye adsorption capability in dark. Instead, enhanced total removal efficiency (∼97%) is obtained when the initial adsorption is succeeded by photodegradation under UV. Direct reusability tests show that even after the third cycle, very high regeneration efficiencies being above 92% are observed for titania-coated nanobeads.     

Influence of the ZrB2 content on the anti-oxidation ability of ZrB2-SiC coatings in aerobic environments with broad temperature range

ZrB₂-SiC coatings with different ZrB₂ contents were prepared by liquid phase sintering. The oxidation processes of coatings were explained according to TG results of ZrB₂-SiC coatings and powders tested from 298 K to 1773 K. Results show that, increasing ZrB₂ content made the weight of the samples changed from weight-loss of 10.04% to weight-gain of 0.14%, while the fastest weight-loss regions were narrowed, whose inflection points reduced from 1310℃ to 1050℃. Increasing ZrB₂ content made the relative oxygen permeability of the ZrB₂-SiC/SiC coatings reduced from 40%–60% to -10%-5%. Increasing ZrB₂ content enhanced high-temperature stability of coatings, making final weight of samples changed from weight-loss of 0.16% to weight-gain of 0.11% after oxidation at 1773 K for 200 h. The peeling and dispersion of Zr-oxides formed Zr-B-Si-O compound glass layer, presenting enhanced stability, dispersion strengthening and pinning effect of Zr-oxides, which were responsible for the excellent anti-oxidation protective effect of coatings in a broad temperature region.     

电路电磁兼容建模与仿真

提出了对暴露在任意外场中的传输线进行时频分析的新方法，这种方法非常稳定，它能够与任意的传输线模型和电路仿真方法兼容，并且使用这种方法得到的仿真值和实际值之间的差别小于1％。     

On keys' meanings and modes: the impact of different key solutions on children's efficiency using a mobile phone

The present study investigates the impact of different key solutions of mobile phones on users' effectiveness and efficiency using the devices. In the first experiment, 36 children (9 - 14 years) and in the second experiment 45 young adults (19 - 33 years) completed four common phone tasks twice consecutively on three simulated phones that had identical menus, but different key solutions. An approach was undertaken to quantify the complexity of keys in three models, incorporating different factors contributing to the keys' complexity (number of key options, number of modes and number of modes with a semantically dissimilar meaning), in order to predict users' performance decrements. As a further main factor, the degree of the users' locus of control (LOC) was measured and interactions with performance outcomes were studied. As dependent measures, the number of inefficient keystrokes, the number of tasks solved and the processing time were determined. Results showed a significant effect of control key solutions on users' efficiency and effectiveness for both children and young adults. Moreover, children's LOC values significantly interacted with performance: children with low LOC values showed the lowest performance and no learnability, especially when using keys with a high complexity. From the three factors contributing to the complexity of keys, keys exerting different functions with semantically inconsistent meanings had the worst effect on performance. It is concluded that in mobile user interface design keys with semantically inconsistent meanings should be generally avoided.