Experimental study and model predictions on helium release in an enclosure with single or multiple vents

This paper presents experiments performed at Canadian Nuclear Laboratories (CNL) to examine the dispersion behaviour of helium in a polycarbonate enclosure that was representative of a residential parking garage. The purpose was to gain a better understanding of the effect of buoyancy- or wind-driven natural ventilation on hydrogen dispersion behaviour. Although hydrogen dispersion studies have been reported extensively in the literature, gaps still exist in predictive methods for hazard analysis. Helium, a simulant for hydrogen, was injected near the centre of the floor with a flow rate ranging from 5 to 75 standard litres per minute through an upward-facing nozzle, resulting in an injection Richardson number ranging between 10^?1 and 10². The location of the nozzle varied from the bottom of the enclosure to near the ceiling to examine the impact of the nozzle elevation on the development of a stratified layer in the upper region of the enclosure. When the injection nozzle was placed at a sufficiently low elevation, the vertical helium profile always consisted of a homogenous layer at the top overlaying a stratified layer at the bottom. To simulate outdoor environmental conditions, a fan was placed in front of each vent to examine the effect of opposing or assisting wind on the dispersion. The helium transients in the uniform layer predicted with analytical models were in good agreement with the measured transients for most tests. Model improvements are required for adequately predicting transients with primarily stratified profiles or strong opposing wind.     

Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

An experimental study of adaptive control for evolutionary algorithms

In this paper, we investigate how adaptive operator selection techniques are able to efficiently manage the balance between exploration and exploitation in an evolutionary algorithm, when solving combinatorial optimization problems. We introduce new high level reactive search strategies based on a generic algorithm's controller that is able to schedule the basic variation operators of the evolutionary algorithm, according to the observed state of the search. Our experiments on SAT instances show that reactive search strategies improve the performance of the solving algorithm.     

A new numerical algorithm to check the observability and bad-data processing ability of the metering scheme

This paper provides a unified approach for the optimization of measurements placements employed for power system online monitoring through state estimation. The proposed methodology, which can be suitable for the mixed measure system, preserves state estimation observability and bad-data processing capability by employing numerical algorithms for observability checking, critical measurements and critical couple identification. First, node injection radix measurements and measurement categories are defined. According to the above definitions, the coefficient matrix can be solved. The analysis on the column vectors of the coefficient matrix can determine each measurement classification. Furthermore, the numbers of each measurement class contains can determine bad-data processing capability. The observability can be checked by the type number of measurements. The proposed method is illustrated with the IEEE39-bus system and the IEEE118-bus system. Results from the case studies are presented to demonstrate that the approach adequately fulfills the desired properties related to observability, bad-data processing, cost, and robustness.     

Mathematical representation of radiality constraint in distribution system reconfiguration problem

Distribution systems are most commonly operated in a radial configuration for a number of reasons. In order to impose radiality constraint in the optimal network reconfiguration problem, an efficient algorithm is introduced in this paper based on graph theory. The paper shows that the normally followed methods of imposing radiality constraint within a mixed-integer programming formulation of the reconfiguration problem may not be sufficient. The minimum-loss network reconfiguration problem is formulated using different ways to impose radiality constraint. It is shown, through simulations, that the formulated problem using the proposed method for representing radiality constraint can be solved more efficiently, as opposed to the previously proposed formulations. This results in up to 30% reduction in CPU time for the test systems used in this study.     

两阶段领域自适应学习

针对领域自适应问题中源域和目标域的联合分布差异最小化问题,提出两阶段领域自适应学习方法.在第一阶段考虑样本标签和数据结构的判别信息,通过学习一个共享投影变换,使投影后的共享空间中边缘分布的差异最小.第二阶段利用源域标记数据和目标域非标记数据学习一个带结构风险的自适应分类器,不仅能最小化源域和目标域条件分布差异,还能进一步保持源域和目标域边缘分布的流形一致性.在3个基准数据集上的实验表明,文中方法在平均分类准确率和Kappa系数两项评价指标上均表现较优.     

Rogowski coil current transducer compensation method for harmonic active power error

In the harmonic active power measurement, the highest uncertainties are generally introduced by the current and voltage transducers. In a previous paper, the authors showed that the current transformer (CT) can introduce significant errors in such measurement, especially if the phase shift between voltage and current is close to ±90°. In such condition the errors on harmonic power measurement are mainly due to the CT phase displacement. This paper shows that better results can be achieved with more linear transducers, such as the Rogowski coil current transducers (RCCTs), whose metrological performance in distorted condition can be improved, by means of a proper compensation method. The proposed method for RCCTs compensation is based on the frequency response and it allows to reduce the errors on harmonic power measurement, also for phase shift close to ±90°. The study is supported by several experimental tests.     

Models for solar radiation prediction based on different measurement sites

The modeling of solar radiation for forecasting its availability is a key tool for managing photovoltaic (PV) plants and, hence, is of primary importance for energy production in a smart grid scenario. However, the variability of the weather phenomena is an unavoidable obstacle in the prediction of the energy produced by the solar radiation conversion. The use of the data collected in the past can be useful to capture the daily and seasonal variability, while measurement of the recent past can be exploited to provide a short term prediction. It is well known that a good measurement of the solar radiation requires not only a high class radiometer, but also a correct management of the instrument. In order to reduce the cost related to the management of the monitoring apparatus, a solution could be to evaluate the PV plant performance using data collected by public weather station installed near the plant. In this paper, two experiments are conducted. In the first, the plausibility of the short term prediction of the solar radiation, based on data collected in the near past on the same site is investigated. In the second experiment, the same prediction is operated using data collected by a public weather station located at ten kilometers from the solar plant. Several prediction techniques belonging from both computational intelligence and statistical fields have been challenged in this task. In particular, Support Vector Machine for Regression, Extreme Learning Machine and Autoregressive models have been used and compared with the persistence and the k-NN predictors. The prediction accuracy achieved in the two experimental conditions are then compared and the results are discussed.     

基于射频技术的无刷同步电机励磁电流的检测

无刷同步电机的励磁系统对励磁电流的测量是制约该励磁方式发展的一大障碍。设计了一个射频系统可以用来解决同步电机的励磁电流的测量问题。该系统可以方便地检测到同步电机励磁机的整流二极管的工作状态并且可以动态地显示励磁电流，极大地方便了运行人员做出判断，而且结构简单、方便实用。     

高导电性原油电脱盐工艺研究

南阳原油中金属含量较高,掺有部分3次采油采出原油,加工时易造成电脱盐装置原油乳化,电导率高,脱盐难度较大。装置投产十几年来脱后含盐一直不合格,经过改造仍然超标,常压塔顶腐蚀严重。为此,对原油进行了电脱盐工艺条件及破乳剂研究,研制出了高效电脱盐设备和生物复合脱盐剂及降电流剂,采用平流弓形电极进行改造,解决了该原油的电脱盐问题,使脱后含盐达到3 mg/L。