Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Silver-plated polyamide fabrics with high electromagnetic shielding effectiveness performance prepared by in situ reduction of polydopamine and chemical silvering

In this article, the silver-plated polyamide fabrics (SPPAFs) with high electroconductibility and shielding effectiveness were fabricated by using in situ reduction of polydopamine and chemical silvering. The effects of SPPAFs dopamine (C₈H₁₁O₂N) and silver nitrate (AgNO₃) concentration on surface resistivity and electromagnetic interference shielding effectiveness were studied. The results showed that the surface resistivity of SPPAFs can reach a minimum value of 0.06 ± 0.014 Ω cm⁻¹, when C₈H₁₁O₂N concentration is 4 g L⁻¹ and the AgNO₃ concentration is 120 g L⁻¹. The shielding effectiveness of SPPAFs in the wide frequency range of 10–3000 MHz increases with the increase in the concentration of AgNO₃, and increases first and stabilizes afterward with increasing C₈H₁₁O₂N concentration. When the concentration of C₈H₁₁O₂N and AgNO₃ is 3 and 120 g L⁻¹, respectively, mean shielding effectiveness values in the low-, medium-, and high-frequency bands are 71.3, 73.8, and 76.1 dB, respectively. Moreover, the mean shielding effectiveness values is 83.79 dB in the frequency range of 1.2–2.3 GHz. The dominant shielding mechanism of SPPAFs is the reflected electromagnetic waves and the absorption shielding effectiveness is less than 2 dB. The average electromagnetic shielding values of SPPAFs are above 67 dB after 16 weeks of storage, when C₈H₁₁O₂N concentration is 4 g L⁻¹ and the AgNO₃ concentration is 80 and 100 g L⁻¹. The prepared SPPAFs show promising applications in military textiles and smart wearable clothing. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48227.     

Fabrication of core–shell nanocomposites with enhanced photocatalytic efficacy

The current study establishes the unprecedented involvement in the evolution and production of novel core–shell nanocomposites composed of nanosized titanium dioxide and aniline‐o‐phenylenediamine copolymer. TiO₂@copoly(aniline and o‐phenylenediamine) (TiO₂@PANI‐o‐PDA) core–shell nanocomposites were chemically synthesized in a molar ratio of 5:1 of the particular monomers and several weights of nano‐TiO₂ via oxidative copolymerization. The construction of the TiO₂@PANI‐o‐PDA core–shell nanocomposites was ascertained from Fourier transform IR spectroscopy, UV–visible spectroscopy and XRD. A reasonable thermal behavior for the original copolymer and the TiO₂@PANI‐o‐PDA core–shell nanocomposites was investigated. The bare PANI‐o‐PDA copolymer was thermally less stable than the TiO₂@PANI‐o‐PDA nanocomposites. The core–shell feature of the nanocomposites was found to have core and shell sizes of 17 nm and 19–26 nm, respectively. In addition, it was found that the addition of a high ratio of TiO₂ nanoparticles increases the electrical conductivity and consequently lowers the electrical resistivity of the TiO₂@PANI‐o‐PDA core–shell nanocomposites. The hybrid photocatalysts exhibit a dramatic photocatalytic efficacy of methylene blue degradation under solar light irradiation. A plausible interpretation of the photocatalytic degradation results of methylene blue is also demonstrated. Our setup introduces a facile, inexpensive, unique and efficient technique for developing new core–shell nanomaterials with various required functionalities and colloidal stabilities. © 2018 Society of Chemical Industry     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

Effects of Ti,Y, and Hf additions on the thermal properties of ZrB2

Reactive hot pressing was utilized to synthesize and densify four ZrB₂ ceramics with impurity contents low enough to avoid obscuring the effects of dopants on thermal properties. Nominally pure ZrB₂ had a thermal conductivity of 141 ± 3 W/m K at 25 °C. Additions of 3 at% of Ti, Y, or Hf decreased the thermal conductivity by 20 %, 30 %, and 40 %, respectively. The thermal conductivity of (Zr,Hf)B₂ was similar to ZrB₂ synthesized from commercial powders containing the natural abundance of Hf as an impurity. This is the first study to demonstrate that Ti and Y additions decrease the thermal conductivity of ZrB₂ ceramics and report intrinsic values for thermal conductivity and electrical resistivity of ZrB₂ containing transition metal additions. Previous studies were unable to detect these effects because the natural abundance of Hf present masked the effects of these additions.     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

DC/DC电源中的电磁干扰及其对策

概述了电磁干扰(EMI)和电磁兼容(EMC)的基本知识，对DC／DC电源中的电磁干扰进行了综合分析，并给出了各自的解决方案。     

大港白水头地区低阻油气层测井评价

在对白水头地区低阻油层的地质特征、物性特征及成因环境进行了分析研究后 ,应用测井曲线特征集法 ,把白水头油田常规油气层、低阻油气层、油水同层、水层等看成是独立的地质事件 ,建立了它们与测井曲线特征之间的对应关系 ,利用这种关系对未知地质事件进行了预测划分。最后根据所建模型定量计算储层各种参数 ,收到了良好的地质效果 ,表明测井曲线特征集法对于识别多成因的低阻油层是一种有效方法     

用Simadyn-D改造宝钢150t电弧炉整流器控制系统

宝钢炼钢厂150 t电弧炉是我国目前最大的直流电弧炉,2003年对其整流器控制系统进行了改造。新系统采用的硬件是西门子公司的Simadyn-D系统,采用CFC编程环境。由于新系统可以与冶炼弧流模型紧密结合,因此保证了在各冶炼阶段调节器性能的最优。