LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

衍射法细丝直径的精密测量

分析了激光衍射法测量细丝直径技术中影响精度的几个主要因素，研究了一种微弱衍射条纹的精密处理及识别技术，有效地提高了测量精度，实测结果表明，文中讨论的技术能在１０￣５０μｍ的范围内实现正负０．１μｍ的重复精度，分辨力优于０．０１μｍ。     

Augmenting Trees to Meet Biconnectivity and Diameter Constraints

Given a graph G=(V,E) and a positive integer D , we consider the problem of finding a minimum number of new edges E' such that the augmented graph G'=(V,E\cup E') is biconnected and has diameter no greater than D. In this note we show that this problem is NP-hard for all fixed D , by employing a reduction from the DOMINATING SET problem. We prove that the problem remains NP-hard even for forests and trees, but in this case we present approximation algorithms with worst-case bounds 3 (for even D ) and 6 (for odd D ). A closely related problem of finding a minimum number of edges such that the augmented graph has diameter no greater than D has been shown to be NP-hard by Schoone et al. [21] when D=3 , and by Li et al. [17] when D=2. Received April 19, 1999; revised June 5, 2001.     

Diameter NASREQ协议在卫星移动通信系统中的应用研究

如何对接入网络的用户进行身份认证、授予相应权限并进行计费,是卫星移动通信系统网络管理需解决的重要问题。简要介绍认证、授权、计费(AAA)的基本概念,分析Diameter协议框架、协议原理以及协议应用于网络接入的特点。阐述协议中包含的各种应用,给出Diameter NASREQ应用的一种系统模型。重点研究Diameter NASREQ协议在卫星移动通信系统中的应用,详述应用中客户机和服务器中各模块的功能和工作原理。通过分析,说明该应用的可行性及有效性。     

Highly ordered anodic alumina nanotemplate with about 14 nm diameter

A novel method for the fabrication of highly ordered nanopore arrays with very small diameter of 14 nm was demonstrated by using low-temperature anodization. Two-step anodization was carried out at 25 V, sulfuric acid concentration of 0.3 M, and electrolyte temperature of −15 °C. After anodization, a regular pore array with mean diameter of 14 nm and interpore distance of 65 nm was formed. The pore diameter and regular arrangement were confirmed by scanning electron microscopy (SEM) and fast Fourier transformation (FFT), respectively. The present results strongly suggest that the diameter of pores in a highly ordered alumina template can be reduced by lowering the anodization temperature.     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

步进电机细分及其在光电测径系统中的应用

叙述了步进电机的细分技术及其测长原理。作为一种测长手段应用于工件直径测量系统中，为提高步进电机细分测长的精度，系统采用了软件补偿的办法，应用光电定位和ＭＣＳ—５１单片机实施控制，构成一种测量范围在１～１００ｍｍ，精度较高，效费比高的光电测径系统。     

Optimizing the Vacuum Heat-Treatment of Hot-Work Tool Steels by Linear Elastic Fracture Mechanics

Linear elastic fracture mechanics was used to optimize the vacuum heat-treatment procedures for conventional hot-work AISI H11 tool steel. The fracture toughness was determined with non-standard, circumferentially notched and fatigue-precracked tensile-test specimens. The fracture-testing method is sensitive to changes caused by variations in the microstructure resulting from the austenitizing and tempering temperatures as well as the homogeneity of the material itself. The combined tempering diagram- Rockwell-C hardness, Fracture toughness K_Ic, Tempering temperature was used for the choice of the vacuum heat-treatment parameters necessary to obtain the best properties for a given application with respect to the investigated steel.     

Microstructural changes in concretes with sulfate exposure

In prior papers the responses of concretes to 50,000 ppm MgSO₄ exposure depending on cement type, w/cm and the presence of slag were described. The present paper completes this analysis by examining the effects of immersion of concretes produced using slag blended cements, in solutions containing 50,000 ppm of sodium sulfate. The spatial evolution of microstructure associated with carbonation and sulfate attack show differences which can be related to the nature of the cation associated with the sulfate, the cement type, and the w/cm ratio.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。