Hydrocarbon-based electrode ionomer for proton exchange membrane fuel cells

The electrode ionomer is a key factor that significantly affects the catalyst layer morphology and fuel cell performance. Herein, sulfonated poly(arylene ether sulfone)-based electrode ionomers with polymers of various molecular weights and alcohol/water mixtures were prepared, and those comprising the alcohol/water mixture showed a higher performance than the ones prepared using higher boiling solvents, such as dimethylacetamide; this is owing to the formation of the uniformly dispersed ionomer catalyst layer. The relation between ionomer molecular weight for the same polymer structure and the sulfonation degree was investigated. Because the chain length of polymer varies with molecular weight and chain entanglement degree, its molecular weight affects the electrode morphology. As the ionomer covered the catalyst, the agglomerates formed were of different morphologies according to their molecular weight, which could be deduced indirectly through dynamic light scattering and scanning electron microscopy. Additionally, the fuel cell performance was confirmed in the current-voltage curve.     

Investigation on sulphonated zinc oxide nanorod incorporated sulphonated poly (1,4-phenylene ether ether sulfone) nanocomposite membranes for improved performance of microbial fuel cell

Hydrothermally prepared zinc oxide nanorods are sulphonated (S–ZnO NR) and incorporated into 15% Sulphonated Poly (1,4-Phenylene Ether Ether Sulfone) (SPEES) to improve the hydrophilicity, water uptake and ion transfer capacity. Water uptake and ion transfer capacity increased to 34.6 ± 0.6% and 2.0 ± 0.05 meq g^?1 from 29.8 ± 0.3% and 1.4 ± 0.04 meq g^?1 by adding 7.5 wt% S–ZnO NR to SPEES. Morphological studies show the prepared S–ZnO NR is well dispersed in the polymer matrix. SPEES +7.5 wt% S–ZnO NR membrane exhibits optimum performance after three-weeks of continual operation in a fabricated microbial fuel cell (MFC) to produce a maximum power density of 142 ± 1.2 mW m^?2 with a reduced biofilm compared to plain SPEES (59 ± 0.8 mW m^?2), unsulphonated filler incorporated SPEES (SPEES + 7.5 wt% ZnO, 68 ± 1.1 mW m^?2) and Nafion (130 ± 1.5 mW m^?2) thereby suggesting its suitability as a sustainable and improved cation exchange membrane (CEM) for MFCs.     

The growth of oleaginous Rhodotorula glutinis in an internal-loop airlift bioreactor by using mixture substrates of rice straw hydrolysate and crude glycerol

The conversion of lignocellulosic biomass (LCB) to microbial oils is attracting a growing amount of attention. However, the growth of the oleaginous yeast Rhodotorula glutinis on LCB hydrolysate (mainly rice straw) only will lead to a low lipid mass fraction, in the range of 10–20%. This study shows that the addition of crude glycerol to the LCB hydrolysate medium can efficiently raise the lipid mass fraction to the range of 30–40%. Crude glycerol is a by-product in the biodiesel production process. The use of renewable LCB hydrolysate and crude glycerol would greatly reduce the substrate cost for microbial oil production using R. glutinis. In addition, the results of experiments show that a low-cost airlift bioreactor is a more suitable fermentation process for the growth of R. glutinis than the use of a conventional agitation tank. When using mixed carbon sources of LCB hydrolysate with 30 kg m⁻³ of reducing sugars and 30 kg m⁻³ of crude glycerol, a maximal cell mass of 21.4 kg m⁻³ and lipid mass fraction of 58.5 ± 6.2 were achieved in an internal loop airlift bioreactor, and this process may have the potential to be applied in scale-up production.     

二氧化碳加氢直接合成二甲醚催化剂的研究——沉淀次序对复合催化剂结构和性能的影响

以草酸乙醇溶液为沉淀剂,采用不同的沉淀次序(并流、反加和正加)制备了CuO-ZnO-Al2O3/HZSM-5复合型催化剂,对CO2加氢直接合成二甲醚反应的催化活性顺序为:并流法催化剂>反加法催化剂>正加法催化剂。3种复合催化剂的还原温度由低到高的顺序为:并流法催化剂<反加法催化剂<正加法催化剂。在沉淀过程中,反加法和正加法均形成类胶体沉淀,相应催化剂的比表面积也较大。IR研究发现,催化剂在1101cm-1处表现Cu/Zn/Al氧化物与HZSM-5分子筛之间相互作用的IR吸收峰强度与其催化活性间存在对应关系。XRD结果表明,并流法得到的催化剂前驱体中有铜锌同形取代现象,有利于催化剂活性的发挥。     

分子筛绿色化合成技术的开发

对现有分子筛合成废液中氨氮及还原性物质的来源进行分析，确定降低排放废水中氨氮浓度及COD的方案。对现有ZRP-5分子筛制备流程进行优化，增加母液及赶胺水回用工序；建立母液浓缩装置，将钛硅分子筛及Β分子筛的合成母液及重排母液应用于ZSM-5分子筛的合成，实现废液的梯级利用。上述措施既解决了因分子筛生产废液的排放造成的环境污染，亦因废物资源化降低了ZSM-5分子筛的生产成本。     

溶剂对环氧乙烷催化水合制乙二醇的影响

研究了NY催化剂催化环氧乙烷水合制乙二醇(EG)过程中,溶剂、催化剂添加量和水与环氧乙烷的摩尔比(简称水比)对EG选择性的影响。实验结果表明,以丙三醇作为溶剂使催化剂进行循环,能提高EG的选择性,效果好于以生成的EG作为溶剂循环催化剂。催化剂添加量、水比和溶剂添加量对EG选择性具有较大影响,其中溶剂添加量对EG选择性的影响最显著。在低水比(1.0~4.0)条件下,EG质量分数小于30%、催化剂质量分数大于7.2%时,EG选择性稳定在95.63%~97.92%,平均值为96.80%,此结果对于进一步降低EG合成工艺的能耗具有指导意义。     

SIMULATION STUDIES OF THE REMOVAL OF WATER FROM ETHANOL BY A CATALYTIC DISTILLATION PROCESS

A new approach based on catalytic distillation (CD) technology was proposed to remove water from ethanol. Isobutylene was introduced to react with water in the CD column. The commercial software simulation tool Aspen Plus was used to investigate the effects of key design factors such as operating pressure and temperature, reactant ratios, reflux and distillate to feed ratios, number of separation and reaction stages, and feed and reaction zone location. It was found that the CD technology offers potential advantages of reduced energy consumption and reduced capital cost over traditional approaches for the removal of water from ethanol.     

Fluorescence and IR characterization of epoxy cured with aliphatic amines

Cure reactions of the stoichiometric mixtures of diglycidyl ether of bisphenol A (DGEBA) and two very low molecular weight aliphatic polyether diamines (PED) were studied by using fluorescence and mid- and near-IR spectroscopic techniques. As the cure proceeded, the primary amine groups in PED are converted to the secondary and the tertiary amines. Near-IR spectral analysis was used to calculate the concentration of the three amine groups as a function of cure time. The decrease in the fluorescence intensity of DGEBA at about 307 nm was observed due to more effective quenching of the tertiary amine groups in PED, in comparison to the primary and the secondary amine groups. A large decrease in fluorescence intensity at 75 and 95 °C cure was observed. The amount of all the amine species was estimated from NIR spectra to shed light on the cure kinetics of PPO (polypropylene oxide) in comparison with PEO (polyethylene oxide) epoxy, as well as to explain their fluorescence behavior.The fluorescence intensity changes were correlated to the extent of epoxy reaction obtained by mid- and near-IR spectroscopy.