Numerical investigations on flashback dynamics of premixed methane-hydrogen-air laminar flames

Injecting hydrogen into the natural gas network to reduce CO₂ emissions in the EU residential sector is considered a critical element of the zero CO₂ emissions target for 2050. Burning natural gas and hydrogen mixtures has potential risks, the main one being the flame flashback phenomenon that could occur in home appliances using premixed laminar burners. In the present study, two-dimensional transient computations of laminar CH₄ + air and CH₄ + H₂ + air flames are performed with the open-source CFD code OpenFOAM. A finite rate chemistry based solver is used to compute reaction rates and the laminar reacting flow. Starting from a flame stabilized at the rim of a cylindrical tube burner, the inlet bulk velocity of the premixture is gradually reduced to observe flashback. The results of the present work concern the effects of wall temperature and hydrogen addition on the flashback propensity of laminar premixed methane-hydrogen-air flames. Complete sequences of flame dynamics with gradual increases of premixture velocity are investigated. At the flame flashback velocities, strong oscillations at the flame leading edge emerge, causing broken flame symmetry and finally flame flashback. The numerical results reveal that flashback tendency increase with increasing wall temperature and hydrogen addition rate.     

Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

Studying the effect of organo-modified nanoclay loading on the thermal stability,flame retardant,anti-corrosive and mechanical properties of polyurethane nanocomposite for surface coating

Clay polyurethane nanocomposite (CPN) coating films were fabricated by uniformly dispersing nanoclay, organically modified with 25–30 wt.% octadecylamine in varying concentrations up to 5 wt.%, in a commercial two component, glossy, acrylic aliphatic polyurethane using ultrasonication. Organo-modified nanoclay was characterized by X-ray diffraction (XRD). The dispersion of the nanoclay into the matrix was investigated by scanning electron microscopy (SEM). CPN coating films were characterized by thermogravimetric analysis (TGA), and flame retardant, corrosion resistance and mechanical properties were also investigated. The XRD measurement indicated that, the organo-modified nanoclay particles were mainly constituted of montmorillonite with traces of quartz and calcite also found to be present. The SEM analysis showed that the nanoclay layers were dispersed and intercalated into the polyurethane coating. Thermogravimetric analysis showed that incorporating 5 wt.% organo-nanoclay into polyurethane considerably enhanced the thermal stability and increased the char residue to 14.11 wt.% relative to 4.58 for the sample without organo-nanoclay (blank polyurethane). The limiting oxygen index (LOI) test revealed that incorporation of organo-nanoclay led to a further increase in LOI values, which indicate an improvement in flame retardancy properties. The corrosion resistance also improved and this improvement increases with increase nanoclay wt.%. The mechanical resistance measurements demonstrated that the gloss of the CPN coating films slightly decreased, although hardness, adhesion and impact resistance of the CPN coating films improved with the incorporation of the organo-nanoclay.     

Investigation of flame spray synthesized La1-xSrxCoO3 perovskites with promotional catalytic performances on CO oxidation

To enhance the activity of catalysts for CO removal, the perovskite-type catalysts La_1-xSr_xCoO₃ (x = 0, 0.2, 0.4, 0.6, and 0.8) with different Sr²⁺ doping amount were synthesized by flame spray synthesis (FSS) method. The perovskite-type catalyst synthesized by FSS has a much larger specific surface area (SSA) than that prepared by other conventional methods. The SSA of catalyst increases with the increase of Sr²⁺ doping amount and the SSA of La_0.2Sr_0.8CoO₃ reaches 31.65 m²/g. Compared with other conventional methods, FSS method significantly improves the activity of catalyst and makes it close to the performances of catalysts with surface modification. The substitution of La³⁺ by Sr²⁺ promotes the generation of secondary phase Co₃O₄ and SrCO₃. The catalytic activity of La_1-xSr_xCoO₃ increases with the addition of Sr²⁺, which results from the increasing active sites and oxygen vacancies. Interestingly, La_0.4Sr_0.6CoO₃ performs the highest activity for CO oxidation and the CO conversion reaches 50% at 148.6 °C and 90% at 165.9 °C. The oxidation of CO over La_1-xSr_xCoO₃ catalyst may follow a combination of MvK and L-H mechanisms according to the experimental results of H₂-TPR. Moreover, the catalyst exhibits good catalytic activity in consecutive oxidation cycles. In consecutive oxidation experiments with La_0.4Sr_0.6CoO₃, the CO conversion reaches 50% at 168.8 °C and 90% at 197.8 °C in the eighth oxidation cycle. These results prove that FSS method can further improve the activity of catalysts and is suitable for the preparation of efficient catalysts.     

Flame Front Deformation Instabilities of Filtration Combustion for Initial Thermal Perturbation

The flame front deformation instability of low-velocity filtration combustion within an inert packed bed is studied based on the initial preheating non-uniformity. Based on the experimental phenomena, an initial thermal perturbation model is numerically proposed so as to predict the deformation behaviors of the flame front instabilities. The numerical prediction indicates that the assumption of an initial thermal perturbation is a feasible explanation as the cause of the flame front inclination instability. As the initial thermal perturbation increases, the phenomena of the flame front break and shrinking instabilities could easily occur at high filtration velocity or low equivalence ratio. Moreover, the evolutions of the flame front break rate and the shrinking rate are quantitatively analyzed.     

燃煤电厂融合多信号光纤火焰检测器的开发研究

介绍一种新型光纤燃煤炉火焰检测器，阐述其系统组成及特点，并提出了基于模糊推理的多信号融合处理方法。     

火焰原子吸收法测定高铋物料中的铅

本文介绍了在以高铋物料为基体 ,5 %的HNO3 介质中 ,波长 2 17nm处进行火焰原子吸收法测定铅的试验 ,采用标准加入法进行回收率的试验 ,回收率大于 98% ,特征浓度为 0 .0 7μg/ml,结果令人满意 ,能满足炉前样分析的要求     

钼酸盐阻燃抑烟剂研发现状

简要地叙述了钼酸盐类阻燃抑烟剂 ,如八钼酸铵、钼酸锌、钼酸钙、钼酸钴和三氧化钼等阻燃抑烟剂的研发现状     

New developments in speciality polymers: polymeric stabilizers

Many new speciality polymers have been developed in the last few years. In this paper polymeric stabilizers (antioxidants, flame retardants and ultraviolet stabilizers) will be discussed. Polymeric antioxidants of the hindered-phenol type, copolymers of 2,6-ditertiarybutyl-4-vinyl(or isopropenyl)phenol with styrene, methyl methacrylate, or more importantly butadiene or isoprene have been prepared; hydrogenation of the latter copolymers gave copolymers of the two polymerizable phenolic antioxidants with ethylene or ethylene/propylene. The polymeric antioxidants have been blended with diene polymers and selected polyolefins and have improved the long-term oxidative stability of these polymers. Polymeric flame retardants have been prepared by copolymerizing styrene and/or acrylonitrile with acrylates and methacrylates of aliphatic bromine-containing alcohols or bromine-containing phenols. Polymers with polymer-bound flame retardants have a higher limiting oxygen index compared with the original polymer. A new class of polymerizable ultraviolet stabilizers has also been developed; these stabilizers are styryl, α-methylstyryl, acryloyl and methacryloyl derivatives of 2(2-hydroxyphenyl)2H-benzotriazoles. These monomers have been copolymerized with styrene, acrylates and methacrylates. 2(2-Hydroxyphenyl)2H-benzotriazoles substituted in the 4 position of the benzotriazole ring with hydroxyl, acetoxy or carboxyl groups suitable for incorporation into polyesters, polycarbonates, polyamides and epoxy resins have also been synthesized. All 2(2-hydroxyphenyl)2H-benzotriazole ultraviolet absorbers and the polymers into which they are incorporated have high light absorbency with γ_max between 330 and 350 nm and extinction coefficients in some cases as high as 4.5 × 10⁴ 1 mol^?1 cm^?1.     

Formation and investigation of epoxy intumescent compositions modified by active additives

Results are reported of research on intumescent composites based on epoxy resin cross‐linked with polyethylene polyamine and containing ammonium polyphosphate and such modifying additives as calcium borate, manganese dioxide, nickel, and chromium, containing tubulenes as gas‐formers and carbonization stimulators. The changes in composition and physicochemical properties of modified compositions under conditions of heat and fire were investigated by X‐ray photo‐electron spectroscopy, atomic force microscopy, and local force spectroscopy. Ammonium polyphosphate mainly stimulates carbonization processes on the inner surface of a bubble being formed during foam coke formation. The introduction of metal‐containing tubulenes leads to the formation of fire‐retardant and low flammability‐compositions with high coke and carbon structures content. The use of calcium borate in the compositions considerably increases the strength of foam coke being formed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1477–1483, 2002