Numerical investigations on flashback dynamics of premixed methane-hydrogen-air laminar flames

Injecting hydrogen into the natural gas network to reduce CO₂ emissions in the EU residential sector is considered a critical element of the zero CO₂ emissions target for 2050. Burning natural gas and hydrogen mixtures has potential risks, the main one being the flame flashback phenomenon that could occur in home appliances using premixed laminar burners. In the present study, two-dimensional transient computations of laminar CH₄ + air and CH₄ + H₂ + air flames are performed with the open-source CFD code OpenFOAM. A finite rate chemistry based solver is used to compute reaction rates and the laminar reacting flow. Starting from a flame stabilized at the rim of a cylindrical tube burner, the inlet bulk velocity of the premixture is gradually reduced to observe flashback. The results of the present work concern the effects of wall temperature and hydrogen addition on the flashback propensity of laminar premixed methane-hydrogen-air flames. Complete sequences of flame dynamics with gradual increases of premixture velocity are investigated. At the flame flashback velocities, strong oscillations at the flame leading edge emerge, causing broken flame symmetry and finally flame flashback. The numerical results reveal that flashback tendency increase with increasing wall temperature and hydrogen addition rate.     

Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

Studying the effect of organo-modified nanoclay loading on the thermal stability,flame retardant,anti-corrosive and mechanical properties of polyurethane nanocomposite for surface coating

Clay polyurethane nanocomposite (CPN) coating films were fabricated by uniformly dispersing nanoclay, organically modified with 25–30 wt.% octadecylamine in varying concentrations up to 5 wt.%, in a commercial two component, glossy, acrylic aliphatic polyurethane using ultrasonication. Organo-modified nanoclay was characterized by X-ray diffraction (XRD). The dispersion of the nanoclay into the matrix was investigated by scanning electron microscopy (SEM). CPN coating films were characterized by thermogravimetric analysis (TGA), and flame retardant, corrosion resistance and mechanical properties were also investigated. The XRD measurement indicated that, the organo-modified nanoclay particles were mainly constituted of montmorillonite with traces of quartz and calcite also found to be present. The SEM analysis showed that the nanoclay layers were dispersed and intercalated into the polyurethane coating. Thermogravimetric analysis showed that incorporating 5 wt.% organo-nanoclay into polyurethane considerably enhanced the thermal stability and increased the char residue to 14.11 wt.% relative to 4.58 for the sample without organo-nanoclay (blank polyurethane). The limiting oxygen index (LOI) test revealed that incorporation of organo-nanoclay led to a further increase in LOI values, which indicate an improvement in flame retardancy properties. The corrosion resistance also improved and this improvement increases with increase nanoclay wt.%. The mechanical resistance measurements demonstrated that the gloss of the CPN coating films slightly decreased, although hardness, adhesion and impact resistance of the CPN coating films improved with the incorporation of the organo-nanoclay.     

Investigation of flame spray synthesized La1-xSrxCoO3 perovskites with promotional catalytic performances on CO oxidation

To enhance the activity of catalysts for CO removal, the perovskite-type catalysts La_1-xSr_xCoO₃ (x = 0, 0.2, 0.4, 0.6, and 0.8) with different Sr²⁺ doping amount were synthesized by flame spray synthesis (FSS) method. The perovskite-type catalyst synthesized by FSS has a much larger specific surface area (SSA) than that prepared by other conventional methods. The SSA of catalyst increases with the increase of Sr²⁺ doping amount and the SSA of La_0.2Sr_0.8CoO₃ reaches 31.65 m²/g. Compared with other conventional methods, FSS method significantly improves the activity of catalyst and makes it close to the performances of catalysts with surface modification. The substitution of La³⁺ by Sr²⁺ promotes the generation of secondary phase Co₃O₄ and SrCO₃. The catalytic activity of La_1-xSr_xCoO₃ increases with the addition of Sr²⁺, which results from the increasing active sites and oxygen vacancies. Interestingly, La_0.4Sr_0.6CoO₃ performs the highest activity for CO oxidation and the CO conversion reaches 50% at 148.6 °C and 90% at 165.9 °C. The oxidation of CO over La_1-xSr_xCoO₃ catalyst may follow a combination of MvK and L-H mechanisms according to the experimental results of H₂-TPR. Moreover, the catalyst exhibits good catalytic activity in consecutive oxidation cycles. In consecutive oxidation experiments with La_0.4Sr_0.6CoO₃, the CO conversion reaches 50% at 168.8 °C and 90% at 197.8 °C in the eighth oxidation cycle. These results prove that FSS method can further improve the activity of catalysts and is suitable for the preparation of efficient catalysts.     

Flame Front Deformation Instabilities of Filtration Combustion for Initial Thermal Perturbation

The flame front deformation instability of low-velocity filtration combustion within an inert packed bed is studied based on the initial preheating non-uniformity. Based on the experimental phenomena, an initial thermal perturbation model is numerically proposed so as to predict the deformation behaviors of the flame front instabilities. The numerical prediction indicates that the assumption of an initial thermal perturbation is a feasible explanation as the cause of the flame front inclination instability. As the initial thermal perturbation increases, the phenomena of the flame front break and shrinking instabilities could easily occur at high filtration velocity or low equivalence ratio. Moreover, the evolutions of the flame front break rate and the shrinking rate are quantitatively analyzed.     

PP－g－AA的制备和表征

用熔融接枝方法制备了聚丙烯－ｇ－丙烯酸（ＰＰ－ｇ－ＡＡ）。用光电子能谱，广角Ｘ射线衍射，红外光谱和化学滴定方法对接枝物进行了定性和定量表征。讨论了单体和引发剂浓度对接枝率的影响，确定了用红外光谱法测定接枝物含量的经验公式     

辐照技术在聚丙烯材料制备和改性中的应用

利用辐照的手段,来制备功能化的聚丙烯材料,在获得新功能的同时,不改变聚丙烯原有的优点,并综述了辐照技术在聚丙烯材料制备和改性中的研究及应用情况     

燃煤电厂融合多信号光纤火焰检测器的开发研究

介绍一种新型光纤燃煤炉火焰检测器，阐述其系统组成及特点，并提出了基于模糊推理的多信号融合处理方法。     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Rheological properties of polypropylene modified by high‐intensity ultrasonic waves

A new method using high‐intensity ultrasonic waves, instead of peroxide‐aided reactive extrusion, was applied to modify a linear polypropylene into a branched structure. The ultrasonic waves induced chain scission and created reactive macromolecules of polypropylene successfully in the melt state without any peroxide. To enhance and control the recombination reaction during sonication, a multifunctional agent and an antioxidant were used. The rheological property measurements clearly confirmed that the modified polypropylene had a nonlinear branched structure. It showed shear‐thinning behaviors in its viscosities at low frequencies, high elastic behaviors in Cole–Cole plots, and a high rheological polydispersity index in comparison with a linear polypropylene. The degradation or recombination of polypropylene was adequately controlled by an antioxidant, which stabilized the structure during sonication. Also, the use of an antioxidant was quite effective in improving the extrusion processability by delaying the instability of the extrudate to a higher shear rate. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006