New horizon in mechanochemistry—high-temperature,high-pressure mechanical synthesis in a planetary ball mill—with magnesium hydride synthesis as an example

A new route of materials synthesis, namely, high-temperature, high-pressure reactive planetary ball milling (HTPRM), is presented. HTPRM allows for the mechanosynthesis of materials at fully controlled temperatures of up to 450 °C and pressures of up to 100 bar of hydrogen. As an example of this application, a successful synthesis of magnesium hydride is presented. The synthesis was performed at controlled temperatures (room temperature (RT), 100, 150, 200, 250, 300, and 325 °C) while milling in a planetary ball mill under hydrogen pressure ($>$50 bar). Very mild milling conditions (250 rpm) were applied for a total milling time of 2 h, and a milling vial with a relatively small diameter (φ = 53 mm, V = ～0.06 dm³) was used. The effect of different temperatures on the synthesis kinetics and outcome were examined. The particle morphology, phase composition, reaction yield, and particle size were measured and analysed by scanning electron microscopy, X-ray diffraction, differential scanning calorimetry (DSC) techniques. The obtained results showed that increasing the temperature of the process significantly improved the reaction rate, which suggested the great potential of this technique for the mechanochemical synthesis of materials.     

Effect of nanosilica addition on bioactivity and in vivo properties of calcium aluminate cement

This study aims at assessing the influence of nanosilica on the bioactivity and mechanical properties of calcium aluminate cement. For this purpose, nanosilica was applied as a replacement for calcium aluminate cement at 0, 2, 5 and 8 wt%. The main components were analyzed by scanning electron microscope coupled with surface imaging and elemental analysis, fourier transform infrared spectroscopy and X-ray diffraction analysis. To estimate the bioactivity of specimens, hydroxyapatite formation on the surface of cement paste was investigated in the simulated body fluid solution. In addition, in vivo evaluation of calcium aluminate cement was performed in subcutaneous tissue of rats. To investigate the mechanical properties, both compressive and flexural strengths were also measured. The results revealed that by increasing nanosilica up to 8 wt%, the strength enhanced. Moreover all cement paste samples with various amounts of nanosilica represented good bioactivity because of formation of bonelike apatite layer on the surface of specimens within 28 days after soaking in simulated body fluid. In vivo experiments indicated that the cement sample was absorbed by the tissue and there was no infection at the implant site. Based on the in vitro and in vivo results, the specimen with 2 wt% nanosilica represented the highest bioactivity.     

The effect of Na addition on the first hydrogen absorption kinetics of cast hypoeutectic Mg–La alloys

With superior properties of Mg such as high hydrogen storage capacity (7.6 wt% H/MgH₂), low price, and low density, Mg has been widely studied as a promising candidate for solid-state hydrogen storage systems. However, a harsh activation procedure, slow hydrogenation/dehydrogenation process, and a high temperature for dehydrogenation prevent the use of Mg-based metal hydrides for practical applications. For these reasons, Mg-based alloys for hydrogen storage systems are generally alloyed with other elements to improve hydrogen sorption properties. In this article, we have added Na to cast Mg–La alloys and achieved a significant improvement in hydrogen absorption kinetics during the first activation cycle. The role of Na in Mg–La has been discussed based on the findings from microstructural observations, crystallography, and first principles calculations based on density functional theory. From our results in this study, we have found that the Na doped surface of Mg–La alloy systems have a lower adsorption energy for H₂ compared to Na-free surfaces which facilitates adsorption and dissociation of hydrogen molecules leading to improvement of absorption kinetic. The effect of Na on the microstructure of these alloys, such as eutectic refinement and a density of twins is not highly correlated with absorption kinetics.     

Effect of Ni/tubular g-C3N4 on hydrogen storage properties of MgH2

Additive doping is one of the effective methods to overcome the shortcomings of MgH₂ on the aspect of relatively high operating temperatures and slow desorption kinetics. In this paper, hollow g-C₃N₄ (TCN) tubes with a diameter of 2 μm are synthesized through the hydrothermal and high-temperature pyrolysis methods, and then nickel is chemically reduced onto TCN to form Ni/TCN composite at 278 K. Ni/TCN is then introduced into the MgH₂/Mg system by means of hydriding combustion and ball milling. The MgH₂–Ni/TCN composite starts to release hydrogen at 535 K, which is 116 K lower than the as-milled MgH₂ (651 K). The MgH₂–Ni/TCN composite absorbs 5.24 wt% H₂ within 3500 s at 423 K, and takes up 3.56 wt% H₂ within 3500 s, even at a temperature as low as 373 K. The apparent activation energy (E_a) of the MgH₂ decreases from 161.1 to 82.6 kJ/mol by the addition of Ni/TCN. Moreover, the MgH₂–Ni/TCN sample shows excellent cycle stability, with a dehydrogenation capacity retention rate of 98.0% after 10 cycles. The carbon material enhances sorption kinetics by dispersing and stabilizating MgH₂. Otherwise, the phase transformation between Mg₂NiH₄ and Mg₂NiH_0.3 accelerates the re/dehydrogenation reaction of the composite.     

The effect of synthesis conditions on the physicochemical properties of magnesium aluminate materials

Magnesium aluminate-based materials were prepared by applying different methods: (i) mechanochemical milling of the initial mixture of magnesium and aluminium nitrate powders (in appropriate stoichiometric amounts) followed by heat treatment at temperatures of 650 °C and 850 °C and (ii) melting of the mixture of nitrate precursors at 240 °C followed by thermal treatment at 650 °C, 750 °C and 850 °C. The effect of synthesis method on the structure and morphology of the obtained solids was studied by using various techniques such as: nitrogen adsorption-desorption isotherms, powder XRD, IR spectroscopy and SEM. It was shown that the mechanochemical milling performed before calcination procedure leads to obtaining of nanocrystalline magnesium aluminate spinel phase at lower temperature of 650 °C in comparison with the method using thermal treatment only (at 750 °C). The obtained nanomaterials exhibit mesoporous structure.     

Enhancement of thermal,mechanical, ignition and damping response of magnesium using nano-ceria particles

Magnesium (Mg)-based nanocomposites owing to their low density and biocompatibility are being targeted for transportation and biomedical sectors. In order to support a sustainable environment, the prime aim of this study was to develop non-toxic magnesium-based nanocomposites for a wide spectrum of applications. To support this objective, cerium oxide nanoparticles (0.5?vol%, 1?vol%, and 1.5?vol%) reinforced Mg composites are developed in this study using blend-press-sinter powder metallurgy technique. The microstructural studies exhibited limited amounts of porosity in Mg and Mg-CeO₂ samples (< 1%). Increasing presence of CeO₂ nanoparticles (up to 1.5?vol%) led to a progressive increase in microhardness, dimensional stability, damping capacity and ignition resistance of magnesium. The compressive strengths increased with the increasing addition of the nanoparticles with a significant enhancement in the fracture strain (up to ~48%). Superior energy absorption was observed for all the composite samples prior to compressive fracture. Further, enhancement in thermal, mechanical and damping characteristics of pure Mg is correlated with microstructural changes due to the presence of the CeO₂ nanoparticles.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

天然气空气绝热转化制合成气催化剂研究

制备了天然气空气绝热转化催化剂,采用固定床反应器进行稳定性评价试验,对反应前后的催化剂进行了分析表征。结果说明,天然气和空气绝热转化反应放热形成的高温对催化剂有烧结作用,使催化剂晶体结构发生了变化,起活性作用的金属镍和氧化铝载体转化为镍铝尖晶石结构的物质。进一步的试验表明,在1050～1300℃的温度可以把催化剂的晶体结构改变。     

Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.     

Effects of zirconium silicate and chromite addition on the microstructure and bulk density of magnesia–magnesium aluminate spinel-based refractory materials

Six synthesized magnesium aluminate spinel-based refractory compositions used in steel and cement applications, were prepared using a two stage sintering process at 1760 °C, starting with approximately 1:1 wt% ratio of pure magnesia and alumina with additions of zirconium silicate (0.5, 1.0 and 2.0 wt%) and chromite (2.0, 3.0 and 5.0 wt%). These compositions were investigated for effects on densification, chemical and mineralogical phases formed.