杭州湾南岸滩涂沉积物中HCHs与DDTs污染特征分析

摘 要：目的 了解六六六（hexachlorocyclohexanes,HCHs）与滴滴涕(dichloro diphenyl trichloroethanes,DDTs)在杭州湾南岸滩涂沉积物中的污染现状。方法 于2018年4月，采集杭州湾南岸地区4个采样点不同深度（0~80 cm）滩涂沉积物，利用气相色谱-串联质谱法（gas chromatography tandem mass spectrometry, GC-MS/MS）测定了该区域中HCHs与DDTs的含量，对其分布规律进行分析，使用共识沉积物质量基准法对其生态学风险进行了评估。结果 所有样品中均检出，HCHs与DDTs含量分别为4.20~6.24 μg/kg与3.37~4.73 μg/kg，主要以β-HCH、δ-HCH以及DDE为主，其污染主要来源于历史性工业品，整体污染处于较低水平；20.3%的沉积物样品中DDEs含量以及28.1%的样品DDTs总量介于阈值效应浓度(threshold concentration, TECs) 和可能效应浓度(probable effect concentration, PECs)之间。结论 杭州湾南岸沉积物中HCHs与DDTs的污染处于较低水平，具有较小的生态学风险。     

Dye removal by polymer derived ceramic nanobeads

Emulsion processed polymer derived ceramic (PDC) nanobeads are used for Methylene Blue dye removal from aqueous solutions. The PDC nanobeads, produced at 600 °C and 1200 °C pyrolysis, are subsequently coated with titania (anatase). Titania-coated nanobeads show less than 35%, i.e., limited dye adsorption capability in dark. Instead, enhanced total removal efficiency (∼97%) is obtained when the initial adsorption is succeeded by photodegradation under UV. Direct reusability tests show that even after the third cycle, very high regeneration efficiencies being above 92% are observed for titania-coated nanobeads.     

Application of the methylene blue test to cement raw materials

Characterisation of raw materials for Portland cement manufacture by use of the methylene blue adsorption method is discussed. The method is shown to be a simple, convenient ‘rule of thumb’ procedure. It provides a guide to the quantity and type of argillaceous minerals present in a given raw material sample.     

尿素醇解合成碳酸酯类化合物技术进展

综述了用尿素醇解合成碳酸酯类化合物的技术进展 ,重点介绍尿素醇解合成碳酸二甲酯研究现状以及与其它工艺路线的比较 ,另外也介绍了尿素醇解合成长碳链脂肪族和芳香族类碳酸酯的研究进展。     

磷酸二苯酯催化的2-吲哚甲烷胺衍生物的合成

以磷酸二苯酯为催化剂,3-甲基吲哚类化合物与亚胺通过Friedel-Crafts加成反应一步合成了具有广泛药理活性的2-吲哚基甲烷胺类化合物,对反应条件进行优化。结果表明,当n(3-甲基吲哚类)∶n(亚胺)∶n(磷酸二苯酯)=1.0∶2.0∶0.1,其中,磷酸二苯酯0.0025 mmol,1 mL无水二氯甲烷作溶剂,室温下反应0.5 h时,即可得到高收率2-吲哚基甲烷胺类衍生物（85%~90%）。产物经 1HNMR、13CNMR 和 HRMS 进行了结构确定。     

烷基二苯醚的合成

分别以烷基化剂溴代十二烷、溴代十四烷、溴代十六烷与二苯醚反应，制得系列烷基二苯醚产品。通过正相高效液相色谱法监测烷基系二苯醚曲合成，优化其合成工艺。色谱条件为：色谱柱，C18 kromasil（5μm，250×4．6mm）；流动相，体积比V正己烷：V异丙醇=18：1；流速，1mL/min。最佳合成工艺为：各反应物的摩尔比n二苯醚：n催化剂：n澳代烷=1：2：5；反应温度为75℃。反应时间为6h。双十二烷基二苯醚、双十四烷基二苯醚、双十六烷基二苯醚的产率分别为79．62％、72．38％、66．83％。     

微波固化环氧树脂／氨基二苯醚树脂的耐热性能研究

以二苯醚树脂(DPO)为原料，合成了一类新型耐高温树脂一氨基二苯醚树脂(ANDPO)，用作双酚A环氧树脂(EP)的固化剂，以提高环氧树脂的耐热性。采用微波技术固化EP／ANDPO体系。通过FTIR定量研究了EP／ANDPO体系的反应程度，利用差示扫描量热法(DSC)和热重分析法(TG)研究了固化体系的耐热性能，并与热固化进行了比较。结果表明：微波固化显著提高了体系的固化速度和热性能。体系转化率为95％时，400W的微波只需10min即可完成固化，而热固化需要在150℃固化240min。微波固化产物的Tg、表观分解温度TA、温度指数Tzg分别为172．6℃、322℃和200℃。而热固化产品的Tg、TA、Tzg分别为163．5℃、306℃和189℃。两种固化方式所得产品的TA、Tzg均高于目前所用的芳香族胺类固化剂，显著提高了环氧树脂的耐热性能。     

年产200吨4，4’-二氟二苯甲酮（DFBP）的工业化设计及可行性研究

本文在大量实验数据基础上，对4，4’-二氟二苯甲酮(DFBP)进行了年产200吨规模的工业化设计，从技术关键、工艺流程、设备选材、三废治理及成本核算等方面对DFBP工业化设计的可行性进行了评价，该设计有如下特点：工艺简单、合理，操作稳定、安全，三废治理有效，原材料及设备投资少，见效快，适合工业化大生产。     

Synthesis and characterization of aromatic copolyesters containing siloxane linkages in the polymer backbone

A new series of aromatic copolyesters containing siloxane linkages were prepared by the melt polymerization of bisphenol A (BPA) with eugenol end‐capped siloxane (EuSi), diphenyl terephthalate (DPT), and diphenyl isophthalate (DPI) in varying ratio in the temperature range 220–290°C under reduced pressure in the presence of dibutyl tin dilaurate (DBTL) catalyst. The siloxane copolyesters prepared were characterized by FTIR, ¹H‐NMR spectroscopy, solution viscosity, thermogravimetric analysis, differential scanning calorimetry, and X‐ray diffraction. The effect of incorporation of eugenol end‐capped siloxane was studied on the properties of BPA/DPI/DPT copolyesters. The glass‐transition temperature of copolyester was decreased from 184 to 70°C by incorporation of 20% of eugenol end‐capped siloxane. All copolyesters were found to be soluble in commonly used aprotic polar solvents and had film‐forming properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3222–3228, 2006     

The adsorption of dyes from aqueous solution using diatomite

Raw diatomite was calcined at 450 °C for dyes removal from aqueous solution. SEM and FTIR analysis show that the raw diatomite contains organic impurities, which are removed after the calcination. The impurities removal decreases the specific surface area and increases the average pore diameter of raw diatomite, while improves its adsorption capability of dyes. The adsorption isotherm and kinetics experiments of methylene blue onto calcined diatomite were then carried out to investigate the adsorption property. It shows that the adsorption capacity of methylene blue is about 50 mg/g. The adsorption isotherm was fitted by the Langmuir, Freundlich and Redlich-Peterson models, which reveals that the Redlich-Peterson isotherm is the best one. Two kinetic models, pseudo-first order and pseudo-second order, were rearranged for expediently investigating the adsortpion mechanisms. Fitting results show that the pseudo-first-order model is better in describing the adsorption process.