Densification effects on the fracture in fused silica under Vickers indentation

This study investigates the effects of densification on the deformation and fracture in fused silica under Vickers indentation by both the finite element analysis (FEA) and experimental tests. A refined elliptical constitutive model was used, which enables us to investigate the effects of the evolution of yield stress under pure shear and elastic properties with densification. The densification distribution was predicted and compared with experiments. The plastic deformation and indentation stress fields were used to analyze the initiation and morphology of various crack types. The formation mechanism of borderline cracks was revealed for the first time. This study reveals that the asymmetry of the densification distribution and elastic-plastic boundary significantly influences the cracking behavior. Under the Vickers indentation, conical cracks have the largest penetration depth. When these cracks emerge from a region far from the impression, they extend with constant radii to form circles on the sample surface. Otherwise, they tend to be initiated at the centers of the indenter-material contact edges before propagating towards the impression corners with increasing radii. Therefore, the borderline cracks consisting of successive partial conical cracks can form at a low load and makes them the first type of crack to appear.     

In2O3:Ga and In2O3:P-based one-electrode gas sensors: Comparative study

Gas sensing characteristics of one-electrode sensors based on the In₂O₃ ceramics doped by gallium and phosphorus have been discussed. In₂O₃-based ceramic was prepared by sol–gel technology. Ozone, CO, CH₄ and H₂ were used as tested gases. The doping concentration effect on the sensor parameters such as magnitude of response, operating temperature, response and recovery times, sensitivity to the air humidity, and selectivity have been analyzed. It was shown that In₂O₃ doping by Ga and P could be used for the sensor performance optimization. It was assumed that the appearance of the second phase (InPO₄ and Ga₂O₃) and the change of structural parameters, taking place during doping process, were the main factors controlling the change of operating characteristics in In₂O₃:P and In₂O₃:Ga-based sensors.     

聚烯烃催化剂硅胶载体的制备和表征

采用并流共沉淀法制备了适用于聚烯烃催化剂的硅胶载体,为减少颗粒的聚集,在制备过程中添加一种表面活性剂。利用透射电子显微镜(TEM)、比表面积测定(BET)和X射线粉末衍射(XRD)法对制备的硅胶载体进行了表征;考察了在制备硅胶载体过程中原料硅酸钠溶液的浓度、溶液pH以及焙烧温度对产物硅胶载体的物理性能的影响。实验结果表明,硅酸钠溶液的浓度影响硅胶的初始粒子的大小,溶液pH直接影响硅酸钠的水解速率,焙烧温度影响硅胶的孔结构和比表面积。当硅酸钠溶液的浓度为0．2mol／L、溶液pH为8-9、反应温度为70℃、焙烧温度为700℃时,硅胶载体的BET比表面积为242．22m2／g、最可几孔径为16．45 nm、堆密度为0．492 1g/mL,与进口硅胶(Silica Gel 955)的物理性能相近。     

新型壳聚糖/纳米二氧化硅杂化材料的制备与性能

在纳米S iO2颗粒表面引入羟丙基氯活性基团,得到功能化S iO2颗粒,再将羟丙基氯化的S iO2颗粒交联固定在壳聚糖上,制备了一种新型的壳聚糖/纳米S iO2杂化材料(简称杂化材料);通过傅里叶变换红外光谱、透射电镜、扫描电镜方法对杂化材料进行表征,采用热重(TG)分析研究杂化材料的热性能;考察了杂化材料的沉降速率和对金属离子Ca2+和M g2+的吸附能力。电镜分析结果表明,杂化材料微粒为纳米尺度的无机S iO2加强化的微粒,S iO2颗粒分散在材料中,形成均匀的表面;TG分析结果表明,杂化材料的热性能有所提高;沉降实验测得壳聚糖和杂化材料作为吸附剂的沉降时间分别为130.3,68.5s,表明杂化材料的沉降速率比壳聚糖的沉降速率快了近一倍;杂化材料对金属离子Ca2+和M g2+的吸附量分别可达到0.289 3,1.445 6mm ol/g。     

Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

气相二氧化硅生产现状及其在涂料中的应用

介绍了气相二氧化硅国内外生产状况,根据气相二氧化硅在涂料方面的应用特点及主 要技术关键的分析,提出了建议。     

砂岩酸化中水化硅沉淀的影响因素分析

讨论了砂岩酸化中产生水化硅沉淀的反应机理。使高岭土与1.0%HF和多种配比的HCl HF在不同温度(20-90℃)反应不同时间(10-300分钟),用等离子吸收光谱法(ICP)测定酸液中可溶性硅的浓度(mg/L),取某时段测定值的减小量为该时段水化硅沉淀生成量,讨论了多种因素的影响,得到了如下结果和结论。反应温度越高,则高岭土与HF之间的反应越快,形成水化硅沉淀的时间越短,最终生成的沉淀量越大;在HF中加入HCl(使用土酸体系)、减小土酸中HF质量分数、加大土酸中HCl、HF质量分数比,均可使生成沉淀时间延后,使最终生成沉淀量减少。60℃时300分钟沉淀量,在1.0%HF、5.0%HCl 1.0%HF、9.0%HCl 1.0%HF中分别为482、321、201mg/L。提出了在酸化设计与施工中可以采取的6条简便易行的减少水化硅沉淀量的措施。图4表1参6。