300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

In situ formation of multi scale reinforcing phases to improve performance of Al2O3-SiC C castables

In order to improve the physical properties and slag corrosion resistance of refractory materials for hot metal pretreatment, different contents of composite metal powders (CMP) were introduced into Al2O3-SiC-C refractory castables. The effect of CMP on the microstructure, physical properties and slag corrosion resistance of Al2O3-SiC-C refractory castables were studied. The results show that the multi scale reinforcing phases including flake crystals, rod shaped fibers, filamentous fibers and whiskers are in situ formed in the samples with addition of CMP, which result to the improvement of the cold modulus of rupture and cold crushing strength. When the addition of CMP is 6 wt.%, the high temperature modulus of rupture increases by 231%, the thermal shock resistance increases by 77% after thermal shock by water cooling 5 times and the percentage of the slag resistant area reduces by 37.2%.     

Research and application of automatic control system of argon blowing at ladle shroud

Argon blowing at the ladle shroud requires the best flow control strategy to effectively avoid the secondary oxidation of molten steel, slag entrapment and heat loss during the casting of the tundish, and at the same time, give full play to the role of bubbles to remove inclusions. Therefore, an automatic control system for argon blowing at the ladle shroud was proposed. The data collected by S7-300PLC and software programming were used to adjust the argon blowing flow online in real time according to factors such as pouring and continuous pouring. On this basis, PID control algorithm and closed loop control mechanism were used for real time adjustment. The flow control valve ensures theminimum deviation between the actual value of the flow and the set value. The production data of this system in the first quarter of 2021 in a special steel plant show that the proportion of furnaces with an acid soluble aluminum (Als) loss percentage of less than 10% of each steel grade has increased by 5.52%, and the proportion of furnaces with an Als loss percentage of more than 60% has increased from 1% decrease to 0. The actual application results show that the use of the system improves the surface quality of the continuous casting slab and the performance of the final product.     

Effect of partitioning on microstructure and properties of a medium carbon Ti Mo bearing high strength Q&P steel

In order to investigate the effect of partitioning procedures on microstructure and properties of a medium carbon Ti Mo bearing steel, the salt bath experiment, field emission SEM, TEM and tensile tests as well as wear tests were utilized to clarify the microstructural evolution and property changes treated by different partitioning parameters. The results show that the microstructures consist of tempered lath martensite, cementite and (Ti, Mo)C particles. With prolonging partitioning time or increasing partitioning temperature, the amount of laths martensite decreases and thicker martensite plates with blunt boundaries appear. In addition, with increasing partitioning temperature from 310℃ to 400℃, the tensile strength, hardness and low temperature toughness are simultaneously decreased, and the reduction reaches up to about 300MPa, 100HV and 20J, respectively. Finally, the wear performance of the samples partitioned below Ms is obviously better than that of samples partitioned above Ms. The morphology of worn surface of samples partitioned below Ms is characterized by plastic fatigue morphology, while the worn surfaces of samples partitioned above Ms are mainly dominated by grooves.     

直升机发动机超转实验系统的测频设计

本文采用FPGA技术测量直升机发动机转速,介绍了双通道等精度测频的原理,设计了信号调理电路,并在FPGA上设计了Verilog代码,在实际应用中测量直升机发动机转速表现了良好的系统实时性能。     

计算机数据安全存储技术及应用

数据安全是计算机安全问题的核心,对于很多具有高度保密要求的单位,安全地存储重要数据,并且在不需要这些数据时作彻底销毁不被他人恢复是至关重要的。本文详细介绍了数据安全存储技术的发展现状,并结合典型的企业信息安全防护体系设计进一步阐述了如何为具有一定保密要求的部门建立可靠的数据安全防护系统。此外,本文从数据存储和销毁的原理上进行了详细分析,并给出了应用软件及案例的测试说明,提出了安全销毁数据的详细解决方法。     

物联网智能家居系统的研究与设计

智能家居有广阔的应用前景.针对传统家居控制上的缺陷,采用B/S架构设计了智能家居管理系统,采用ZigBee无线网络实现对各类家居设备的信息采集和指令控制.用SQL Server 2005数据库管理系统与家庭网关,进行数据的传递与接收.通过Web浏览器,用户可以实现对智能家居系统的管理.     

N含量对Nb微合金化HRB400E钢筋组织与性能的影响

摘要：为了更好地发挥N元素在Nb微合金化钢筋中的作用,降低生产成本以及为钢筋成分设计提供理论依据。利用金相显微镜、扫描电镜、透射电镜、力学试验机对不同N含量的Nb微合金化高强抗震钢筋进行显微组织表征及力学性能测试,探究N含量对Nb微合金化钢筋的组织与力学性能的影响。研究表明,轧制过程中的奥氏体组织,随着N含量的增加,平均奥氏体晶粒有所减小;最终组织为铁素体和珠光体,随着N含量的增加,铁素体平均晶粒尺寸而减小,片层状珠光体的连续性增加,片层间距减小;析出相Nb(C,N)随着N含量的增大,沉淀析出的第二项颗粒体积分数增大,颗粒尺寸随之减小;在力学性能方面,屈服强度逐渐增加,抗拉强度先增加后减少。     

应变速率对Q460连铸坯高温力学性能的影响

摘要：采用Gleeble-3500热模拟试验机和金相法测试了不同应变速率下建筑用钢Q460连铸坯的高温力学性能,获得了600~1200℃范围内Q460连铸坯的高温强度、热塑性和最终室温组织随拉伸温度和应变速率的变化规律。结果表明,当Q460连铸坯在较高的应变速率（10s-1）下进行高温拉伸时,试样的断面收缩率随着拉伸温度的升高而升高,没有出现高温脆性区;在较低的应变速率（10-3s-1）下进行高温拉伸时,试样的断面收缩率出现了2个脆性区,第1个在1100℃至熔点温度,第2个脆性区间在700℃附近。总体来说,实验钢种的高温断面收缩率均大于65%,表明建筑用钢Q460连铸坯具有较好的高温热塑性。此外,同一应变速率下,Q460连铸坯的抗拉强度随着拉伸温度的升高而降低,而伸长率随着拉伸温度的升高而升高。