Dynamic probe of ZnTe(110) surface by scanning tunneling microscopy

The reconstructed surface structure of the II–VI semiconductor ZnTe (110), which is a promising material in the research field of semiconductor spintronics, was studied by scanning tunneling microscopy/spectroscopy (STM/STS). First, the surface states formed by reconstruction by the charge transfer of dangling bond electrons from cationic Zn to anionic Te atoms, which are similar to those of IV and III–V semiconductors, were confirmed in real space. Secondly, oscillation in tunneling current between binary states, which is considered to reflect a conformational change in the topmost Zn–Te structure between the reconstructed and bulk-like ideal structures, was directly observed by STM. Third, using the technique of charge injection, a surface atomic structure was successfully fabricated, suggesting the possibility of atomic-scale manipulation of this widely applicable surface of ZnTe.     

Performance and Commercial Application of the Promoter LCC-A for Maximization of Propylene Yield

1 Introduction Propylene as an important feedstock for organic chemicals is mainly originated from steam cracking and catalytic cracking processes. During the FCC process the propylene content varies with the FCC catalyst and process technology adopted, resulting in significant difference in propylene concentration in the cracked product——LPG. The conventional FCC pro- cess generally gives a propylene yield of around 4%, while the FCC process with maximization of propylene yield can in…     

Cu基络合物催化甲醇液相氧化羰化反应

针对甲醇液相氧化羰基化法合成碳酸二甲酯(DMC)工艺,开发了新型Cu基络合催化剂(CuB rnLm)。对CuB rnLm催化剂的活性及其稳定性进行了研究。实验结果表明,采用该催化剂,甲醇转化率和DMC选择性较高;元素价态和物质结构分析表明,CuB rnLm催化剂循环使用5次后仍保持较好的稳定性。采用正交设计和中心响应曲面法设计实验,并使用S tatistica软件进行统计分析,寻求出反应的主要影响因素,并得到优化的工艺条件:反应温度100~110℃、反应压力3.0~3.5M Pa、反应时间4~6h、CuB rnLm催化剂质量浓度(以甲醇的体积计)0.15~0.20g/mL。在此工艺条件下,甲醇转化率可达23%以上,DMC的选择性为96%~98%。     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

Effect of oxygenation on electrocatalysis of La0.6Ca0.4CoO3−x in bifunctional air electrode

A vacuum-annealed La_0.6Ca_0.4CoO_3−x was consecutively oxygenated in air at temperatures decreasing from 800 to 100 °C, and its electrocatalytic activities for oxygen reduction and evolution were then measured as a function of the oxygenation temperature. The valence of Co cation, changing between +2 and +3, was found susceptible to annealing either in vacuum or air. The catalytic activities initially decrease monotonically as the oxygenation temperature was decreased from 800 to 300 °C, as a result of increasing oxygen content, and then rise abruptly with the oxygen reduction activity reaching a maximum at 200 °C and the oxidation activity at 150 °C. X-ray photoelectron spectroscopy analysis indicated that the enhancements by the low-temperature oxygenation involved increased OH coverage and less charged cations at surface. The results clearly reveal the importance of the post-calcination annealing process for optimizing the performance of La_0.6Ca_0.4CoO_3−x in air electrode applications.     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

聚合物载体－稀土金属络合物的研究 ⅩⅢ．聚［苯乙烯－甲基丙烯酸β（甲基亚硫酰基）乙酯］的结构与其稀土金属络合物催化丁二烯聚合的活性

从测得的竞聚率计算了单体链节在聚［苯乙烯－甲基丙烯酸β（甲基亚硫酰基）乙酯］（ＰＳＭ）中的序列分布。苯乙烯（Ｓ）或甲基丙烯酸β（甲基亚硫酰基）乙酯（Ｍ）的长序列的概率随着ＰＳＭ中相应单体含量的增加而增加。对于Ｓ和Ｍ摩尔分数大致相等的ＰＳＭ，单体链节的长序列分布函数值相接近。用与此结构相近的ＰＳＭ合成的稀土金属络合物，其催化活性不佳。在Ｍ短序列分布和Ｓ长序列分布较高的情况下，络合物的催化活性最好。所得聚丁二烯的微观结构与ＰＳＭ中单体单元的分布无关。