Prediction of brittle-to-ductile transitions in polystyrene

In this study it is attempted to predict brittle-to-ductile transitions (BDTs) in polystyrene blends, induced either by an increase in temperature or by a decrease in inter-particle distance. A representative, two-dimensional volume element (RVE) of a polystyrene matrix with 20% circular voids, is deformed in tension. During deformation a hydrostatic-stress based craze-nucleation criterion [1] is evaluated. The simulations demonstrate that crazes initiate at low temperatures while a transition from crazing to shear yielding (BDT) is found around 75 °C. The numerical results correlate well with tensile tests on similar heterogeneous polystyrene. The presence of an absolute length, as experimentally found, is more difficult to explain. Near a free surface a T_g-depression is measured for polystyrene and also the resistance to indentation in polystyrene is lower than expected from bulk properties. Both observations are rationalised by an enhanced segmental mobility of chains near a free surface. As a consequence of these findings, an absolute length-scale could be incorporated in the numerical simulations. For simplicity, the length-scale is modelled by taking a temperature gradient over a thin layer near the internal free surfaces of the RVE. Deformation of the RVE with different absolute length-scales shows that indeed also the experimentally found brittle-to-ductile transition can be predicted if the ligament thickness between the inclusions (‘voids’) in polystyrene is below a critical value of ca. 15 nm.     

Solution intercalation of polystyrene and the comparison with poly(ethyl methacrylate)

Polystyrene nanocomposites have been prepared via solution intercalation method. Combination of wide-angle X-ray diffraction and thermogravimetric analysis is used to study the effect of solvents on the morphology of the nanocomposites as a function of the amount of residual solvent. d-Spacing of the polystyrene nanocomposites has a minimum value when the residual solvent concentration is between 2 and 4 wt%. Different interaction level between the solvent molecules and polymer chains is considered to be the reason for this special d-spacing change behavior. By comparing the solution intercalation of polystyrene and poly(ethyl methacrylate) from different solvents, it is concluded that the interactions between polymer-surfactant, solvent-surfactant, and polymer-solvent play important role for the solution intercalation of polymers.     

新型硅蜡乳液的制备

将蜂蜡用复合乳化剂乳化时加入自制的乳化助剂，制得稳定的蜡乳液，将该乳液与羟基蛙油乳液复配，制得乳白色略带蓝光硅蜡乳液，该硅蜡乳液用于绵羊服装革作顶层手感改善剂，除了获得油润的蜡感和滑爽感之外，还使成革具有抗菌和抗静电作用。     

Preparation and Application of Active Composite Antibacterial Material Containing Ag~ and Zn~(2 )

1Introduction Harmfulbacteriaexistanywhereintheworldsuchas soil,air,water,surfacesofobjectsandourskins,etc.Thenumberofbacteriumisenormous,withmanydiffer entspecies.Theyhavethreatenedthehealthofhuman beingsseriously.Withthedevelopmentofeconomyand environme…     

Low Electrical Percolation Threshold of Silver and Copper Nanowires in Polystyrene Composites

Silver and copper nanowires have been synthesized using a scalable method of AC electrodeposition into porous aluminum oxide templates, which produces gram quantities of metal nanowires ca. 25 nm in diameter and up to 5 and 10 μm in length for Ag and Cu, respectively. The nanowires have been used to prepare polystyrene nanocomposites by solution processing. Electrical resistivity measurements performed on polymer nanocomposites containing different volume fractions of metal indicate that low percolation thresholds of nanowires are attained between compositions of 0.25 and 0.75 vol %.     

氧化还原功能纤维的研究 Ⅷ．含正丙胺基吸附剂与Au~（3＋）的氧化还原反应机理

通过元素分析、红外光谱分析、光电子能谱分析以及扫描电子显微镜分析等手段，证实含正丙胺基吸附剂与Ａｕ３＋的氧化还原反应过程中，氮原子邻近的羟基碳或Ｃ－Ｈ键被氧化，而氮原子并未参与氧化还原反应；吸附态Ａｕ（３＋）最终部分被还原成单质金；在非水介质中吸附在吸附剂上的金聚集成颗粒状。     

用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。