Effect of heat treatment on tensile properties of friction stir welded joints of 2219-T6 aluminium alloy

Abstract

The effect of post-weld heat treatment (PWHT) on the tensile properties of friction stir welded (FSW) joints of 2219-T6 aluminium alloy was investigated. The PWHT was carried out at aging temperature of 165°C for 18 h. The mechanical properties of the joints were evaluated using tensile tests. The experimental results indicate that the PWHT significantly influences the tensile properties of the FSW joints. After the heat treatment, the tensile strength of the joints increases and the elongation at fracture of the joints decreases. The maximum tensile strength of the joints is equivalent to 89% of that of the base material. The fracture location characteristics of the heat treated joints are similar to those of the as welded joints. The defect free joints fracture in the heat affected zone on the retreating side and the joints with a void defect fracture in the weld zone on the advancing side. All of the experimental results can be explained by the hardness profiles and welding defects in the joints.     

SURFACE MODIFICATION OF TITANIUM FILMS WITH SODIUM ION IMPLANTATION： SURFACE PROPERTIES AND PROTEIN ADSORPTION

Sodium implanted titanium films with different ion doses were characterized to correlate their ion implantation parameters. Native titanium films and ion implanted titanium films were characterized with combined techniques of X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and light microscopy (LM). The surface presented increased sodium concentration on treated titanium films with ion dose increasing, except for the group with the highest ion dose of 4× 1017 ions/cm2. XPS depth profiling displayed that sodium entered titanium film around 25-50 nm depth depending on its implantation ion dose. AFM characterization showed that sodium ion implantation treatment changed the surface morphology from a relatively smooth titanium film to rough surfaces corresponding to different implantation doses.After sodium implantation, implanted titanium films presented big particles with island structure morphology. The surface morphology and particle growth displayed the corresponding trend.Fibrinogen adsorption on these titanium films was performed to correlate with the surface properties of treated titanium films. The results show that protein adsorption on ion-implanted samples with dose of 2 × 1017 and 4 × 1017 are statistically higher (p ＜ 0. 01) than samples treated with dose of 5×1016 and 1 ×1017, as well as the control samples.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Characterisation of FR-4 substrate with various plasma treatment conditions

Abstract

The effects of plasma treatment on the surface of the flame resistant-4 (FR-4) substrate with underfills under various treatment conditions (operating gas, operating time, operating power) are investigated by using contact angle measurement, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The plasma treatment on substrate surfaces increased the oxygen containing functional groups or the polar component of the surface free energy, improving the wetting characteristics of the underfills/FR-4 substrates. The plasma treatment conditions which minimised the contact angle between the underfills and FR-4 substrates were an operating power of 300 W and operating time of 180 s under Ar gas atmosphere.     

Impact of slag–refractory lining reactions on the formation of inclusions in steel

Abstract

The present study was carried out to investigate the impact of slag– refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling.     

Effects of heat treatment processes on microstructure and properties of 2·25Cr–1Mo–0·25V HSLA steels

Abstract

In the present paper, the effects of the heat treatment processes with two conditioning treatments and four quenching–tempering processes on the mechanical properties of 2·25Cr–1Mo–0·25V high strength low alloyed (HSLA) steel are investigated. The results show that the conditioning treatments have obvious effects on the low temperature impact energy but little effect on the tensile strength. The elevation of the final austenitising temperature increases the strength, whereas it results in the decrease in the low temperature impact energy due to the coarse microstructure. The results of the fracture surfaces analysis further make sure that the fracture surfaces of tensile specimens all exhibit ductile characters with a lot of dimples. However, the fracture surfaces of impact specimens exhibit two typical fracture characters, i.e. the ductile and brittle fracture surface corresponding to the fine and coarse microstructures respectively. In addition, the elongation and reduction in area seem to be insensitive to the heat treatments. Meanwhile, the impact fracture mode is more sensitive to the grain size and not to the low temperature impact energy.     

Development of precipitate size and volume fraction of niobium carbonitrides in stabilised stainless steel

Abstract

Niobium carbonitride (NbX) precipitates have been studied in a niobium stabilised austenitic stainless steel AISI type 347 with approximate nominal composition Fe–0.06C–17.5Cr–11.4Ni–0.8Nb. The steel was extruded to seamless tube, solution annealed at 1100°C for 3 min, water quenched, and subsequently isothermally aged at 700°C for times up to 70 000 h. Size distribution and volume fraction of the coarse distribution (1–10 µm) of NbX particles were measured using scanning electron microscopy (SEM). The fine distribution (～30 nm) was investigated using energy filtered transmission electron microscopy (EFTEM). Size distribution and volume fraction were determined using jump ratio images. Coarse NbX (～0.3% volume fraction) precipitates were formed during solidification and extrusion, and were little affected by solution annealing and isothermal aging. Fine NbX (～0.5% volume fraction) precipitates formed during solution annealing and grew during the first 800 h of aging. Precipitate size determination using EFTEM appears to give accurate results, while volume fraction determination requires homogeneous material for good results.     

A magnetic resonance compatible surgical manipulator: part of a unified support system for the diagnosis and treatment of heart disease

A prototype of a magnetic resonance (MR)-compatible surgical manipulator was designed and evaluated. The manipulator is designed so as to fit into vertical magnetic field open-configuration MR imagers. Moreover, it is designed to work without being fixed to an MR imager, and its electrical circuits and lines of actuators and sensors are independent of the room shield so that it could be installed in various kinds of settings at many MR imager sites without any additional construction. The MR compatibility of the manipulator was evaluated: no noticeable deformation was observed in the MR images even when the manipulator was in motion. Although the signal-to-noise deterioration ratio was higher than that previously reported, the MR images were thought to be good enough for recognizing the whole structure of a targeted organ and for following the relative position of the manipulator tip with regard to the target, i.e. MR tracking.     

Utilisation of silicon rubber to characterise tool surface quality during die compaction

Abstract

A new methodology was developed to observe and measure tool wear and tool surface quality during the die compaction process. The newly developed method is a non-destructive test that relies on silicon rubber to transcribe the inner surface profile of the compaction die. After verification of the method, aluminium and iron alloy powders were compacted to quantify tool wear and tool surface quality with two die materials, tungsten carbide and tool steel. The tool surface quality was quantified by recording surface roughness of the die replicas on a surface profilometer.     

Influence of cooling and reheating on the evolution of copper rich liquid in high residual low carbon steels

Abstract

This study investigates some effects of austenite microstructure on processes leading to copper hot shortness. Low carbon steels containing 0˙55 wt-% copper were subjected to two thermal profiles in an infrared image furnace with attached confocal scanning laser microscope: hold at 1150°C for 60 s; hold at 1150°C for 60 s, quench to 400°C, reheat to 1150°C. Heat treatments were conducted in dried/deoxidised argon to image microstructures. Subsequent samples were oxidised in air. The oxide/metal interface was studied in a scanning electron microscope. Additional confocal scanning laser microscope experiments involved melting copper directly on the steel. After quench/reheat, austenite grain size decreased by a factor of ～1˙7 and grain boundaries were redistributed. Copper evolved during the first heating was no longer found at boundaries. Results from direct copper exposure reveal an apparent effect of boundary character on copper penetration rate. Possible mechanisms by which hot shortness is affected are discussed.