Utilization of pyrolytic oil and hydrogen enriched syngas from single feedstock (delonix regia) through pyrolysis process and its influence on performance and emission characteristics in CI engine

The main objective of the present investigation is to conduct the performance, combustion and emission analysis of CI engine operated using hydrogen enriched syngas (pyrolytic gas) and biodiesel (pyrolytic oil) as dual fuel mode condition. Both the pyrolytic oil and syngas is obtained from single feedstock delonix regia fruit pod through pyrolysis process and then pyrolytic oil is converted into biodiesel through esterification. Initially biomass is subjected to thermal degradation at various pyrolysis temperature ranges like 350–600 °C. During the pyrolysis process syngas, pyrolytic oil and char are produced. The syngas is directly used in the CI engine and pyrolytic oil is converted into biodiesel and then used in the CI engine. The pyrolytic oil and syngas is subjected to FTIR and GC/TCD analysis respectively. The syngas analysis confirms the presence of various gases like H₂, CH₄, CO₂, CO and C₂H₄ in different proportions. The various proportions of the syngas is mainly depending upon the reactor temperature and moisture content in the biomass. The syngas composition varies with increase in the temperature and at 400 °C, higher amount of hydrogen is present and its composition are H₂ 28.2%, CO is 21.9%, CH₄ is 39.1% and other gases in smaller amounts. The biodiesel of B20 and syngas of 8lpm produced from the same feedstock are considered as test sample fuels in the CI engine under dual fuel mode operation to study the performance and emission characteristics. The study reveals that BTE has slight increase than diesel of 1.5% at maximum load. On the another hand emission like CO, HC and smoke are reduced by 15%,25% and 32% respectively at full load condition, whereas NO_x emission is increased at all loads in the range of 10–15%. Therefore B20+syngas of 8lpm can be used as an alternative fuel in CI engine without any modification and major products from pyrolysis process with waste biomass is fully used as fuel in the CI engine.     

Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method

A new technique of EDM coring of single crystal silicon carbide (SiC) ingot was proposed in this paper. Currently single crystal SiC devices are still of high cost due to the high cost of bulk crystal SiC material and the difficulty in the fabrication process of SiC. In the manufacturing process of SiC ingot/wafer, localized cracks or defects occasionally occur due to thermal or mechanical causes resulted from fabrication processes which may waste the whole piece of material. To save the part of ingot without defects and maximize the material utilization, the authors proposed EDM coring method to cut out a no defect ingot from a larger diameter ingot which has localized defects. A special experimental setup was developed for EDM coring of SiC ingot in this study and its feasibility and machining performance were investigated. Meanwhile, in order to improve the machining rate, a novel multi-discharge EDM coring method by electrostatic induction feeding was established, which can realize multiple discharges in single pulse duration. Experimental results make it clear that EDM coring of SiC ingot can be carried out stably using the developed experimental setup. Taking advantage of the newly developed multi-discharge EDM method, both the machining speed and surface integrity can be improved.     

面向工程应用的单片机课程教学改革与实践

在分析传统单片机教学存在问题的基础上,提出面向工程应用,聚焦企业需要,构建能力递进、面向应用的内容体系,搭建资源共享、实践创新、师生互动的自主学习平台,组建培养兴趣,突出技能的“双师型”教学团队,实践表明,在传授知识的同时,能有效提升学习兴趣,优化人才素质结构。     

烧结机卸料装置耐磨性改善

烧结机导料箱、单辊破碎机和卸料漏斗承载着烧结热矿的导料、破碎与输送,是烧结生产的重要组成部分。高温、重载的工况环境决定着机尾卸料装置必须具有抗磨损、耐高温的特性。针对邯钢1^#435m^2烧结机机尾关键部件耐磨工作面寿命短,更换不方便等问题,分析磨损机理与失效原因,提出改进抗磨工作面结构,升级耐磨材料,优化焊接工艺等措施。通过技术方案的实施,使烧结机导料箱、单辊破碎机和卸料漏斗等卸料装置维持了较高的抗磨损性能,达到了预期的改造效果。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

The development of a single-item Food Choice Questionnaire

Based on the multi-item Food Choice Questionnaire (FCQ) originally developed by Steptoe and colleagues (1995), the current study developed a single-item FCQ that provides an acceptable balance between practical needs and psychometric concerns. Studies 1 (N = 1851) and 2 (2a (N = 3290), 2b (N = 4723), 2c (N = 270)) showed that the single-item FCQ scale has good convergent and discriminant validity. Generally, the results showed the highest correlations with the related multi-item dimensions (>0.40). Study 2 refined the scale. Only the items for convenience (Study 2a), sensory appeal (Study 2b) and mood (Study 2c) needed to be revised (as Study 1 showed a correlation between the multi-item and the single-item below the threshold of 0.60). The results also showed comparable predictive validity. Both methods revealed similar association patterns between food motives and consumption behaviours (Fisher’s z tests revealed agreements of 86.2% for Study 1, 92.9% for Study 2a and 100% for Studies 2b and 2c). Study 3 (N = 6062) showed an example of the added value of a context-specific application for the single-item FCQ. Different motives were shown to be relevant across contexts, and the context-specific motives had additional explained variance beyond the general multi-item FCQ. Studies 2b and 3 also showed the performance of the single-item FCQ in an international context. In sum, the results indicate that the single-item FCQ can be used as a flexible and short substitute for the multi-item FCQ. The study also discusses the conditions that should be considered when using the single-item scale.     

Anchoring single Pt atoms on hollow Ag3VO4 spheres for improved activity towards photocatalytic H2 evolution reaction

The high cost of noble metal catalysts has been a great bottleneck for the catalyst industry. Using the noble metal at a single-atom level for catalytic applications could dramatically decrease the cost. The impacts of single Pt atoms on the photocatalytic performance of Ag₃VO₄ have been investigated and reported. In this report, single Pt atoms were anchored on the surface of Ag₃VO₄ (AVO) as a cocatalyst, and the resultant composite photocatalyst has been studied for photocatalytic H₂ production from water driven by visible light. The as-prepared AVO particles are hollow nanospheres in the monoclinic phase with a bandgap of 2.20 eV. The light absorption edge of AVO/Pt is slightly red-shifted compared to that of the pristine AVO, indicating more visible light absorption of AVO/Pt. The XPS peaks of Ag, V, and Pt exhibit a significant shift after AVO and Pt get into contact, suggesting the strong interaction between the surface Ag and V atoms, and single Pt atoms. After 3-h illumination, the photocatalytic H₂ evolution amount from AVO/Pt is improved up to 1400 μmol, which is 2.8 times that on the bare AVO. Such efficient photocatalytic H₂ evolution on AVO/Pt is still maintained after five reaction cycles. The better photocatalytic performance of AVO/Pt has been attributed to the more efficient visible light utilization and the lower interfacial charge transfer resistance, as demonstrated in the DRS and EIS spectra. The presence of the surface Pt atoms also leads to a higher amount of reactive radicals, which could efficiently promote the surface redox reactions.     

Image Super-Resolution Based on Generative Adversarial Networks: A Brief Review

Single image super resolution (SISR) is an important research content in the field of computer vision and image processing. With the rapid development of deep neural networks, different image super-resolution models have emerged. Compared to some traditional SISR methods, deep learning-based methods can complete the superresolution tasks through a single image. In addition, compared with the SISR methods using traditional convolutional neural networks, SISR based on generative adversarial networks (GAN) has achieved the most advanced visual performance. In this review, we first explore the challenges faced by SISR and introduce some common datasets and evaluation metrics. Then, we review the improved network structures and loss functions of GAN-based perceptual SISR. Subsequently, the advantages and disadvantages of different networks are analyzed by multiple comparative experiments. Finally, we summarize the paper and look forward to the future development trends of GAN-based perceptual SISR.     

DISPERSION COMPENSATION CFBG IN100km 10Gbit／s RECIRCULATING SYSTEMS

A 10Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4×167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of±5GHz. At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.